Contact Us

HXN40043

Brand: Hisiwell
Hisiwell HXN40043 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN40043 — Discrete & Power Semiconductors | Superb Automation

HXN40043

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN40043 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN40043: 79.4 W of continuous wave over 3.4 to 3.9 GHz

The HXN40043 moves the family up into the upper part of S band and the lower edge of C band, covering 3.4 to 3.9 GHz, 500 MHz wide, at 49 dBm saturated, which is 79.4 W, with 11 dB of gain and 50 per cent drain efficiency from a 28 V rail, continuous wave, with plus or minus 0.8 dB of flatness.

At 50 per cent the rail supplies 158.9 W, the drain current is 5.67 A at 28 V, and the heat is 79.4 W. Because the mode is continuous wave, that 79.4 W is a steady load, not an average of a burst, and the heatsink has to hold it indefinitely.

The 28 V rail keeps the part inside a low voltage system, but 5.67 A of continuous current is a real feed: the track from the supply to the flange, the connector and the decoupling all carry it, and the loss in that path is a small but persistent subtraction from the 28 V at the die.

Eleven decibels of gain is the lowest in the family so far, and at 79.4 W it means 6.31 W of drive. That is a packaged power stage rather than a small driver, and the chain has to be planned with the loss of the isolator and the cable already inside the budget.

The parameter rows Hisiwell publishes for HXN40043

Part classGallium nitride power transistor, internally matched
Frequency range3.4 to 3.9 GHz
Bandwidth, calculated500 MHz, 14 per cent fractional
Saturation output power as publishedat least 49 dBm
Saturation output power in watts, calculated79.4 W
Gain as publishedat least 11 dB
Drain efficiency as publishedat least 50 per cent
Drain voltage28 V
Flatness across the bandplus or minus 0.8 dB
Operating modecontinuous wave
Input impedance50 ohm
Output impedance50 ohm
Output at 1 dB compressionnot published, the index prints a slash
DC input at saturation, calculated158.9 W
Drain current at saturation, calculated5.67 A at 28 V
Dissipation at saturation, calculated79.4 W
Dissipation if efficiency falls to 45 per cent, calculated97.1 W
Drive power for the rated output, calculated38 dBm, 6.31 W
Output per 100 MHz of the band, calculated15.9 W
Thermal resistance, junction to casenot published
Package outline and dimensionsnot published in text, one image on the product page
Scattering parametersnot published
Pinch off voltage and gate bias pointnot published on this page
Operating and storage temperaturenot published
Moisture level and floor lifenot published
Orderable addendum and packingnot published
Neighbour at 50 dBm over 4.2 to 4.4 GHzHXN40046, same rail, 10 dB gain
Neighbour below at 49 dBm over the octaveHXN40032 on 2.7 to 3.7 GHz

Seventy nine watts of steady heat on a 28 V bus

Continuous wave changes the cooling question from a transient one to a steady state one, and steady state is easier to answer: 79.4 W on a carrier at 1 C per watt is 79 C of rise over the case, which needs a liquid plate or a large forced air stack; at 0.5 C per watt it is 40 C, which a good heatsink holds; at 3 C per watt it is 238 C, which no part survives.

Because the vendor publishes no junction to case figure, the carrier, the interface and the heatsink have to be chosen from the load and verified on the first article. On a continuous wave part that is simpler than on a pulsed one, because there is no pulse to measure, only a steady case temperature that can be read with a thermocouple after half an hour of operation.

Efficiency at 45 per cent raises the heat to 97.1 W and the current to 6.30 A, a 22 per cent increase on the cooling and on the feed. The 50 per cent row has no typical marker on this part, so it reads as the published value, and a purchase specification that needs a floor should state one.

The supply side is modest but not trivial: 5.67 A at 28 V through a feed with a 0.2 ohm path would drop more than a volt, which is 4 per cent of the rail and a visible loss of output. Keeping the path resistance low matters more than the capacitance here.

Eleven decibels of gain and the driver that goes with it

Six point three one watts of drive is an awkward size: too large for a packaged gain block and too small for the 25 W driver stage used further up the ladder. In practice it means a two stage driver, or a packaged amplifier rated at 10 W and run backed off, and the loss between the driver and this flange has to be included in the budget from the start.

The 11 dB row also sets the sensitivity to the band. Over 500 MHz a gain slope of 1 dB from edge to edge is normal on an internally matched part, so a chain that is flat at 3.65 GHz may be 1 dB down at 3.45 GHz, and the equalisation belongs in the driver rather than in the final stage.

With no compression point published, the gain row describes saturated operation only. A system running this part 3 dB backed off to keep a modulated carrier inside the linear window is working on data that is not on the page, and the backed off gain is lower than 11 dB by definition.

Where a 79.4 W stage over 3.4 to 3.9 GHz fits

The band covers the upper S band radar allocations and the lower edge of C band, including the fixed link and satellite blocks that sit between 3.4 and 3.9 GHz. A continuous wave 79.4 W amplifier is a natural driver for a larger C band stage, a test source for antenna and component work, or a transmitter for a short range link where the antenna does the rest.

It is a poor fit for a passive cooled enclosure, for any application that needs a published compression point, and for a chain that cannot supply 6.31 W of clean drive. Our RF power transistor cross reference work prints the gain floor and the drive of each member of this family, because the driver is often the part of the chain that decides whether the chain is buildable.

The one stop RF supply view groups the flange hardware, the capacitors and the feed parts that a 5.67 A continuous amplifier needs, and it is where a first article bill of materials is usually assembled.

Questions we answer on HXN40043 before a lot is booked

The first is the cooling class. At 79.4 W of steady heat the answer decides whether the part is usable in the enclosure, and it has to come before the mechanical stack is fixed.

The second is the drive budget. Eleven decibels leaves no room for a long cable or a lossy isolator, so the driver is part of the same question as the final stage.

The third is the lot. With no addendum and no marking published, the purchase order names the band, the rail and the mounting, and the incoming inspection plan records the flange and the DC behaviour of each lot. The RF procurement process puts the bias order, the current limit and the case temperature target in front of the vendor before the first shipment.

A hundred watts at the top of the batch is a different question from the ten watt part at the bottom. The rule that holds across the family is that the match, the flange and the cooling all scale with the output while the gain floor falls, and this part sits at the point where the chain stops being a packaged amplifier and starts being two stages. A system that needs 10 W at 3.6 GHz and a system that needs 79.4 W at 3.7 GHz share a band but not a supply, a heatsink or a driver, and the four rows that separate them are the rail, the efficiency, the gain and the mode. Reading those four before the dBm is what keeps a build on schedule, because the part that looks closest on output is often two rails and a driver stage away from the one that fits.