HXN40037
Product Specifications
HXN40037
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40037 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40037: 251 W at 55 per cent efficiency over 2.7 to 2.9 GHz
The HXN40037 is the 54 dBm member of this family, covering 2.7 to 2.9 GHz from a 50 V rail in 100 microsecond pulses at 10 per cent duty. The published rows are saturated output at least 54 dBm, gain at least 13 dB, drain efficiency at least 55 per cent typical, 50 ohm ports and plus or minus 0.8 dB of flatness. The efficiency row is the interesting one: 55 per cent typical is the highest printed anywhere in the S band group of this family, and it changes the heat budget more than the output figure does.
Fifty four dBm is 251.2 W. At 55 per cent the DC input is 456.7 W, the drain current at 50 V is 9.13 A and the dissipation is 205.5 W during the pulse. Compared with the 57 dBm member on the same band, this part delivers half the output for 62 per cent of the dissipation, which is the usual trade at the top of a power ladder and the reason a system often settles one step below the largest device.
The band, 2.7 to 2.9 GHz, is the classical S band radar window, and a 200 MHz span at this power with an internal match is what a radar or an instrumentation transmitter needs. Two hundred microseconds is a short pulse for radar and a long one for a communication burst; the 10 per cent duty cycle means the average dissipation is 20.6 W, which is a modest thermal load on a carrier that has to survive 205 W for a fifth of a millisecond.
The drive is 41 dBm, or 12.6 W, from the 13 dB gain row. That is the lowest drive requirement of the 54 dBm and above parts in this group, and it is worth noting when a chain is being planned: a 54 dBm part that needs 12.6 W of drive can sit behind a packaged driver, while the 57 dBm and 58 dBm members on the same band need 31.6 W and 41.7 W and generally need a power stage in front of them.
The parameter rows Hisiwell publishes for HXN40037
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 2.7 to 2.9 GHz |
| Saturation output power as published | at least 54 dBm |
| Saturation output power in watts, calculated | 251.2 W |
| Gain as published | at least 13 dB |
| Drain efficiency as published | at least 55 per cent, typical |
| Drain voltage | 50 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | pulsed, 100 microsecond pulse width at 10 per cent duty |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Output at 1 dB compression | not published, the index prints a slash |
| DC input at saturation, calculated | 456.7 W |
| Drain current at saturation, calculated | 9.13 A at 50 V |
| Dissipation during the pulse, calculated | 205.5 W |
| Average dissipation at 10 per cent duty, calculated | 20.6 W |
| Average drain current at 10 per cent duty, calculated | 0.91 A |
| Drive power for the rated output, calculated | 41 dBm, 12.6 W |
| Charge drawn per pulse, calculated | 0.91 mC |
| Thermal resistance, junction to case | not published |
| Transient thermal impedance | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published on this page |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Same band, higher output | HXN40038 at 57 dBm and 48 per cent efficiency |
| Same band, wider window | HXN42002 over 2.7 to 3.1 GHz from a 48 V rail |
What 55 per cent efficiency is worth at 251 W
Efficiency is where the money goes on a pulsed part, and the spread across this family shows it. At 45 per cent this device would dissipate 307 W and draw 11.2 A from the rail; at 48 per cent, 272.1 W and 10.5 A; at 55 per cent, 205.5 W and 9.13 A. The difference between the 45 per cent case and the published typical is 101 W of heat and 2 A of pulse current, for the same 251 W of radio frequency.
A 101 W reduction in dissipation is the difference between a forced air heatsink and a liquid cooled plate on a compact assembly, and it is also 101 W less load on the vehicle or cabinet supply. That is why the efficiency row deserves a minimum in the purchase specification, and why a buyer should be suspicious of a part offered as equivalent on output power alone with a lower efficiency figure: the supply and the cooling are sized by that row, not by the dBm.
The same arithmetic sets the average load. At 10 per cent duty the published typical gives 20.6 W of average dissipation; the 45 per cent case gives 30.7 W. On a carrier of 0.5 C per watt that is 10 C against 15 C of average rise, which looks trivial until the ambient is 70 C and the junction ripple during the 200 microsecond pulse is added on top of it.
Short pulses and the thermal question
A 100 microsecond pulse at 10 per cent duty is a 1 kHz key with the device on for a tenth of each cycle. The average dissipation of 20.6 W is easy to remove; the junction excursion within the pulse is not calculable from anything the vendor publishes, because there is no transient thermal impedance curve. At 205.5 W of instantaneous dissipation, the difference between a die with 0.3 C per watt of transient impedance and one with 1.0 is 60 C against 200 C of excursion, which is the difference between a working part and a failed one.
The practical route is to buy the part with a vendor measurement of case temperature at the rated pulse condition, then measure it on the first article with a thermal camera or a thermocouple in the flange, and to keep the case below the value the family's single full data sheet recommends, which is 75 C. That figure comes from the HX2734P600W document described on the HXN42001 page; it is the only thermal recommendation published anywhere in this family, and it is a case temperature rather than a junction temperature.
The 50 V rail at 9.13 A of pulse current needs a feed with modest energy storage: 0.91 mC per pulse means 2 V of sag costs 0.46 mF, which is a small bank compared with the 398 W members. The inductance of the feed matters more than the capacitance at 200 microseconds, because the leading edge of the pulse is where the droop appears.
Where a 251 W stage at 2.7 to 2.9 GHz fits
The fit is a radar or instrumentation transmitter with a short pulse and a modest average power: airport and weather radar front ends, range instrumentation, satellite S band uplink equipment and laboratory amplifiers for component testing. The 200 MHz window covers the band, the 13 dB gain keeps the driver inside a packaged part, and 55 per cent efficiency keeps the cooling inside a forced air budget.
It is a poor fit for continuous wave, where 205 W of steady dissipation would need a cooling stack that the flange cannot feed, and a poor fit for a long pulse system that keys for milliseconds at the same duty cycle, because the published condition is 200 microseconds. It is also a poor fit for a linear application, since the compression point is not published and the saturated figure is the only power row on the page.
Where a system needs more output on the same band, the step to the 57 dBm member doubles the radio frequency power and raises the dissipation to 543 W during the pulse; where it needs less drive, this part is already the easiest member of the group to drive. Our RF power transistor cross reference work puts the output, the efficiency, the rail and the drive of the three S band members side by side so the step can be priced before it is taken.
Questions we answer about HXN40037 before a lot is booked
The first is the pulse width. Two hundred microseconds is the published condition; a system that keys 1 ms at 10 per cent duty is asking a different question of the same die, and the answer is a measurement rather than a spec sheet row.
The second is the cooling budget. Our defence grade component supply view is where the temperature classes and the screening options for this kind of part are set out, because a radar assembly that runs at a 70 C ambient needs its thermal margin agreed before the vendor is asked for a quote.
The third is the arriving lot. With no moisture level and no order code published, the purchase order names the band, the rail and the pulse condition, and the incoming inspection plan checks the flange, the marking and the DC behaviour at gate and drain. A saturated power sweep at 2.8 GHz is done on the customer bench or at a partner RF laboratory, and the quotation says which.