HXN40035
Product Specifications
HXN40035
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40035 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40035: 100 W continuous wave over 2.7 to 3.5 GHz from 28 V
The HXN40035 is the continuous wave member of this family's S band group, and in a group of pulsed parts that changes the whole engineering question. The published rows are 2.7 to 3.5 GHz, saturated output at least 50 dBm, gain at least 11 dB, drain efficiency at least 50 per cent typical, a 28 V rail, plus or minus 0.8 dB of flatness and 50 ohm ports.
Fifty dBm is 100 W, and continuous wave means those 100 W are produced for as long as the amplifier is keyed, with no duty cycle to divide the heat. At 50 per cent efficiency the DC input is 200 W and the dissipation is 100 W, steady, on a flange in a metal package, with no transient window in which to hide. Everything else on this page follows from that one difference.
The 28 V rail is the other difference. Every other part in this group runs at 48 or 50 V, while this one runs at 28 V, which is the classic vehicle and airborne rail. At 100 W output and 200 W DC input the current is 7.1 A, which is a modest load for a 28 V supply and a convenient one for a system that already has that bus.
The band, 2.7 to 3.5 GHz, is 800 MHz wide and includes the whole S band radar allocation plus the lower part of the 3.5 GHz band used for fixed wireless and satellite links. A continuous wave part with an 800 MHz internal match at 100 W is a general purpose driver or a small transmitter, and it is the part in this group that can be qualified in a thermal chamber at steady state rather than in a pulse rig.
The parameter rows Hisiwell publishes for HXN40035
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 2.7 to 3.5 GHz |
| Saturation output power as published | at least 50 dBm |
| Saturation output power in watts, calculated | 100.0 W |
| Gain as published | at least 11 dB |
| Drain efficiency as published | at least 50 per cent, typical |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Output at 1 dB compression | not published, the index prints a slash |
| DC input at saturation, calculated | 200.0 W |
| Drain current at saturation, calculated | 7.14 A at 28 V |
| Dissipation at saturation, calculated steady state | 100.0 W |
| Drive power for the rated output, calculated | 39 dBm, 7.94 W |
| Band width | 800 MHz |
| Output per 100 MHz of the band, calculated | 12.5 W |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published on this page |
| Quiescent current | not published |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Same band, pulsed, 50 V, 55 dBm | HXN40036 in 100 microsecond pulses at 20 per cent duty |
| Same band, pulsed, 48 V, 57.5 dBm | HXN42012 at 200 microsecond pulse width |
Continuous wave means the thermal answer comes first
One hundred watts of steady dissipation on a metal flange is a solved problem, but only if the interface is right. With no junction to case figure published, the cooling has to be specified from the load and confirmed by measurement. A carrier offering 0.5 C per watt gives 50 C of rise over the case at 100 W, and a 1.0 C per watt carrier gives 100 C, which on a 70 C ambient case is already past the temperature a gallium nitride die should be asked to hold.
That is why the first question on a continuous wave part is not the dBm but the mounting: the flange flatness, the thermal interface material, the torque and the heatsink's ability to hold the case at a sane temperature in the cabinet where the unit will live. A pulsed part can hide a poor interface inside a 10 per cent duty cycle; this one cannot.
Efficiency has the same leverage. At 45 per cent the dissipation at 100 W output rises to 122.2 W and the current to 7.94 A; at 55 per cent it falls to 81.8 W and 6.5 A. On a steady state part that is the difference between two heatsink classes, and because the published figure is a typical with no minimum, the purchase specification should state the number the thermal budget needs rather than accepting the headline.
A 28 V rail and what it changes
Twenty eight volts at 7.1 A is a much easier supply than 48 V at 26 A, and it is the reason this part is attractive for an airborne or vehicle system that already has a 28 V bus. There is no pulse current to bank against in continuous wave, so the supply only has to hold 7.1 A steady with low ripple, and the feed inductance that dominates the pulsed members of this family is not a first order problem here.
The trade is output. One hundred watts from 28 V is a fraction of the 316 W to 631 W that the 48 V and 50 V members deliver, and a system that needs more continuous wave power cannot get it by paralleling two of these without a combiner and the loss that goes with it. Where more output is needed in a pulse, the family has the 55 dBm and 57.5 dBm members on the same band.
The gain of 11 dB means 7.94 W of drive, which is a comfortable level for a packaged driver stage and keeps the chain at two power stages plus a small signal front end.
Where a 100 W continuous wave stage over 2.7 to 3.5 GHz fits
The fit is a driver for a larger pulsed transmitter, a continuous wave test source for antenna and receiver measurements, a small S band transmitter for fixed or mobile systems, and any application on a 28 V bus that needs 100 W over a wide band with an internal match.
It is a poor fit for a system that needs more than 100 W continuously, for a linear multicarrier application where the compression point is unknown, and for a compact assembly without a real thermal path. It is also a poor fit where the system needs a high duty pulsed output at 300 W or more, because the pulsed members of the family exist for exactly that.
The comparison that matters is against the 55 dBm pulsed member on the same band: the same band, the same 50 ohm ports, 5 dB more output, a 50 V rail and a 20 per cent duty cycle. Our RF power transistor cross reference work puts the mode and the rail in the same row as the output precisely so a continuous wave requirement is not filled with a pulsed part, which is a mistake that costs a heatsink and a supply on the first build.
Questions we answer about HXN40035 before a lot is booked
The first is the case temperature the assembly can hold. Without a junction to case figure, the only defensible specification is a measured case temperature at 100 W continuous, taken on the first article in the intended heatsink.
The second is the interface. The flange, the flatness and the mounting hardware decide the thermal path more than the part does, and our defence grade component supply view covers the screening and temperature class questions that usually arrive with a continuous wave S band requirement.
The third is the lot and the bias. No pinch off voltage or quiescent current is published for this part, so the bias point has to come from the vendor or from a measured first article, and the incoming inspection plan records the marking, the flange and the DC behaviour. A saturated power sweep at 3 GHz belongs on the customer bench or at a partner RF laboratory.