HXN40032
Product Specifications
HXN40032
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40032 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40032: 79.4 W continuous wave on the 2.7 to 3.7 GHz band
The HXN40032 is the third step of the Hisiwell ladder over 2.7 to 3.7 GHz, and it is the step where the gain row drops. Saturated output is 49 dBm, which is 79.4 W, on the same 28 V rail and the same plus or minus 0.8 dB of flatness across a full gigahertz, but the published gain is 10 dB rather than the 12 dB carried by the two members below it. Ten decibels at 79.4 W means 7.94 W of drive, which is a power stage rather than a small driver.
The efficiency row is 45 per cent marked typical, and at that figure the rail supplies 176.5 W, the drain current is 6.30 A and the heat is 97.1 W. Ninety seven watts of continuous dissipation is a liquid or heat pipe class load on a flange of this size, and it is the number that decides whether a build chooses this part or two smaller ones combined.
The band remains the reason to consider the family at all. One gigahertz at 28 V with the match on the carrier suits a system that has to cover several allocations with one amplifier: a radar band at the bottom, a fixed link block in the middle, a test tone anywhere inside. The 50 ohm ports mean the amplifier is a two connector block in the chain, and the flatness row means the equalisation is done once rather than per channel.
The construction is the family standard, in-plane matching synthesis on a film hybrid carrier in a metal package, and the vendor states internal matching rather than leaving the match to the user. Nothing on the page describes a tuning option, and none should be expected.
The parameter rows Hisiwell publishes for HXN40032
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 2.7 to 3.7 GHz |
| Bandwidth, calculated | 1000 MHz, 31 per cent fractional |
| Saturation output power as published | at least 49 dBm |
| Saturation output power in watts, calculated | 79.4 W |
| Gain as published | at least 10 dB |
| Drain efficiency as published | at least 45 per cent, typical |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Output at 1 dB compression | not published, the index prints a slash |
| DC input at saturation, calculated | 176.5 W |
| Drain current at saturation, calculated | 6.30 A at 28 V |
| Dissipation at saturation, calculated | 97.1 W |
| Dissipation if efficiency falls to 40 per cent, calculated | 119.1 W |
| Drive power for the rated output, calculated | 39 dBm, 7.94 W |
| Gain per stage with a 2 W driver, calculated | needs 6 dB more than a 2 W driver supplies |
| Output per 100 MHz of the band, calculated | 7.9 W |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, one image on the product page |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published on this page |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Neighbour below on the same band | HXN40031 at 45 dBm and 12 dB gain |
| Neighbour above on the same band | HXN40033 at 52 dBm on a 32 V rail |
Ten decibels of gain is a statement about the match
A 79.4 W part with 10 dB of gain is a part where the match network and the package absorb a large share of the input. The driver has to deliver 7.94 W to produce 79.4 W, and every element between the driver and this flange is subtracted directly: an isolator at 0.4 dB costs 1.3 W of the budget, a connector pair and a short cable another 0.3 dB, and the input return loss of this stage decides how much of the remainder is reflected rather than absorbed.
On the same band a 45 dBm part with 12 dB of gain needs 2 W, so the step from 31.6 W to 79.4 W is a step from a packaged driver to a small power stage. That is a real change in the chain and not a footnote, and it is the reason a system moving up the ladder often stays where it is and adds a second amplifier instead.
The 10 dB row also sets the gain stability question. With no gain against frequency curve published, a plus or minus 0.8 dB flatness in saturated output does not translate into a flat gain response; the two are different quantities, and a cascade of two stages with a low gain floor each is more sensitive to the slope than a single stage with more gain.
The practical consequence is a driver with headroom above 7.94 W, enough to cover the isolation, the cabling and a 1 dB gain shortfall at a band edge, and a chain that is measured end to end rather than assembled from three data sheet rows that each look adequate.
Ninety seven watts and the supply that has to feed it
At 6.30 A of continuous drain current the feed is no longer a decoupling exercise alone. The rail has to hold 28 V at the flange under a load that moves with the modulation, the track from the supply to the device has to carry 6.3 A with a drop that is small against 28 V, and the capacitor bank has to supply the current at the band rather than at the switching frequency of a regulator three boards away.
The thermal side is the harder half. A carrier at 1 C per watt gives 97 C of rise over the case, which is a liquid cooled plate; at 0.5 C per watt it is 49 C, which a large forced air heatsink can hold; at 3 C per watt it is 291 C, which no part survives. The vendor publishes no junction to case figure, so the carrier, the interface and the heatsink have to be chosen from the load and verified on the first article with a thermocouple in the flange.
Efficiency sensitivity is 22 W between 45 and 40 per cent, which on this flange is the difference between a comfortable margin and a marginal one. The typical marking on the efficiency row means the number is not a floor, so the purchase specification should state the number the cooling was built for and the first article should demonstrate it at the centre of the band.
Where 79.4 W over the octave fits
The fit is a continuous wave transmitter or a high power test amplifier over 2.7 to 3.7 GHz: a radar with a continuous wave mode, a satellite S band uplink block at the low end, a fixed link driver, an antenna range amplifier or a laboratory source for high power component testing. In each case 79.4 W is enough to drive an antenna directly and the octave band removes the need for a band switch.
It is a poor fit for a passive cooled enclosure, for any modulated application that needs a published compression point, and for a chain that cannot supply 7.94 W of clean drive at the top of the band. It is also a poor fit where the system needs 158.5 W, because the member above it changes the rail to 32 V and the mode to pulsed, and neither of those carries over from this build. Our RF power transistor cross reference work shows exactly that break in the ladder, with the rail and the mode printed against each output.
Where a second source is being considered, the drop in replacement check starts from the flange, the pin positions and the 50 ohm ports, because two 49 dBm parts in different flanges are not interchangeable in a built assembly even when the electrical rows agree.
Questions we answer on HXN40032 before a lot is booked
The first is the cooling class. At 97.1 W of continuous heat the answer decides whether this part is usable in the enclosure at all, and it has to come before the mechanical stack is fixed rather than after.
The second is the drive budget. Ten decibels of gain leaves no room for a long cable or a lossy isolator, so the driver and the interconnect are part of the same question as the final stage.
The third is the lot documentation. With no addendum and no marking published, the purchase order names the band, the rail and the mounting method, and the incoming inspection plan checks the flange and the DC behaviour of every lot. The RF procurement process is where the current limit, the bias order and the case temperature target are agreed with the vendor before the first shipment.