Contact Us

HXC50118

Brand: Hisiwell
Hisiwell HXC50118 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50118 — Discrete & Power Semiconductors | Superb Automation

HXC50118

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50118 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50118: 170 W on HF to 500 MHz and the smallest single ended rung that still needs a heatsink

The HXC50118 is an LDMOS RF power transistor from Hisiwell on the HF table with a 0.5 GHz top frequency and a 170 W output row. It sits one rung below the 250 W single ended part and one rung above the 80 W row, all three in the same 500 MHz band.

At 170 W the part is small enough that the amplifier can be a single board with a small heatsink, and large enough that the thermal path still decides the rating. That is the awkward middle of the power range: too big for a surface mount footprint with no thermal consideration, too small for a liquid cooled assembly, so the flange, the interface material and the airflow become the engineering content of the product.

The row publishes the frequency, the power, the rail and the mode. It publishes no gain and no efficiency, so the drive and the heat are arithmetic here rather than specification. Both are stated with the assumption attached, because an assumption that is labelled can be replaced by a measurement and an assumption that is not is a guess.

The HXC50118 rows as the vendor publishes them

Part classLDMOS RF power transistor, single ended
Frequency range, index rowHF to 0.5 GHz
Top frequency in MHz, calculated500 MHz
Quarter wavelength at the top, calculated150 mm in air
Saturated output, index row170 W
Output in dBm, calculated52.30 dBm
Step below the 250 W single ended row, calculated1.67 dB
Step above the 80 W single ended row, calculated3.27 dB
Drain rail, index row50 V
Load voltage at 170 W into 50 ohm, calculated92.2 V rms, 130.4 V peak
Peak against the rail, calculated2.61 times
Peak at a two to one mismatch, calculated260.8 V
Load line resistance for 170 W on a 50 V rail, calculated7.4 ohm at the fundamental, rail squared over twice the power
DC input at 55 per cent, calculated309 W, 6.2 A at 50 V, 139 W of heat
DC input at 65 per cent, calculated262 W, 5.2 A at 50 V, 92 W of heat
DC input at 70 per cent, calculated243 W, 4.9 A at 50 V, 73 W of heat
Output per megahertz of window, calculated0.3 W
GainNot published
Drain efficiencyNot published
Mode, index rowCW
Package and flangeNot published
Thermal resistance, junction to caseNot published
Load impedanceNot published, no load pull table
Data sheetNone reachable for this row

A 14.7 ohm load line, 2.61 rail ratio and a simple output network

170 W into 50 ohm is 92.2 V rms and 130.4 V peak, which is 2.61 times the rail. On the device side the fundamental load line is near 7.4 ohm, so the output network transforms the 50 ohm load down to that value with a ratio of 6.8 to 1, comfortably inside what a two section low pass can do at 500 MHz with a few tenths of a decibel of loss.

The 2.61 rail ratio is the lowest on the 500 MHz rows and it is the reason this part is easy to protect. A 200 V capacitor is adequate at the matched condition with margin, and the 260.8 V peak at a two to one mismatch is close enough to 200 V that the rating still has to be reconsidered, but the margin is far easier than on the 1.4 kW row at 374 V peak.

The current is 6.2 A at 55 per cent efficiency and 4.9 A at 70 per cent. A 10 A connector and a modest bulk capacitor bank cover the stage, and the supply does not need to be built around this part. That is what makes a 170 W stage the natural size for a product built on a standard 48 V or 50 V bus.

Cooling 139 W in a small enclosure

At 55 per cent efficiency the part produces 139 W of heat, which is more than a small extruded heatsink will move in still air. In a sealed enclosure the same 139 W raises the internal temperature by whatever the enclosure's thermal resistance allows, and a sealed box of a few litres has a thermal resistance that will not support it without a fan or a cold wall.

The interface between the flange and the heatsink is where small amplifiers usually lose their margin. A 0.5 K per watt interface adds 70 K at 139 W, which on a 25 K ambient already puts the flange near 95 C before the die rise is counted. A 0.15 K per watt interface adds 21 K for the same heat. That difference is worth more than any electrical improvement available on this part.

The vendor publishes no thermal resistance and no flange drawing, so the interface cannot be closed from the row. A buyer who is building a sealed product should request both before committing the mechanical build, and should treat the 139 W figure as the lower bound until an efficiency measurement says otherwise.

What a 170 W stage is used for

The common uses are industrial RF excitation, plasma bias at moderate power, laboratory amplifiers and driver stages for larger transmitters. In the driver role 170 W is 52.30 dBm, which is more drive than most kilowatt stages need, so the part is normally backed off rather than run at saturation, and the backed off efficiency is lower than the saturated figure in any table.

Backing off is where an unpublished gain curve hurts most. A part that delivers 170 W at saturation with 15 dB of gain needs 5.4 W of drive at saturation, and at 6 dB of back off the gain typically falls by a decibel or two, so the drive for 42 W of output is not simply 1.3 W. A buyer planning a backed off stage should measure the gain compression rather than extrapolate from the saturated row.

The other use is as one branch of an external pair. Two 170 W parts combined give 340 W, which is within 0.13 dB of the 350 W row built as an internal pair, and the external version costs two networks and a combiner but allows individual replacement. At this power the arithmetic is close enough that the choice is about serviceability rather than about output.

Where the HXC50118 sits and what it is not

It is not a replacement for the 250 W row: the difference is 1.67 dB and the two parts may not share a footprint. It is not a replacement for the 350 W pair either, which is 3.16 dB above it and requires a balun. What it is, is the smallest single ended part on this table that can still drive a kilowatt stage or serve as a final amplifier in a compact transmitter.

The 80 W row below it is 3.27 dB down and the 30 W row is 7.5 dB down, so the table gives a buyer a choice at every step of roughly 3 dB from 30 W to 250 W in single ended parts. That granularity is useful for product families built at several power levels, because a 3 dB step usually means the same supply and a similar network. The output and rail comparison is on the RF power transistor cross reference page.

What the row does not give is any statement about linearity, ruggedness, or the flange. Those three decide whether the part can be used in a product rather than on a bench, and each one has to be asked for explicitly.

Buying the HXC50118: what the order has to state

State the sub band, the rail, the mode, the flange and body, the quantity, and the gain and efficiency the factory will guarantee. If the part will run backed off, say so and ask for the gain at that drive level, because a saturated gain figure does not describe a backed off stage.

The incoming test should record gain at three frequencies, output at the rated drive and the quiescent current at the bias the amplifier will use. On a part this size the whole test can run on a bench fixture in a few minutes, so it can be done on every unit rather than on a sample. The record structure is on the incoming inspection plan page.

Because a 170 W stage is usually part of a chain, buying it together with the driver and the final stage against one date is the practical route described on the one stop RF supply page. Chain level buying also lets the test plan cover the whole chain rather than three separate parts.

Questions buyers ask about the HXC50118

What is the current draw? 6.2 A at 55 per cent efficiency, 5.2 A at 65 per cent and 4.9 A at 70 per cent, all calculated on a 50 V rail.

Can it be used at 430 MHz? Yes. The window runs to 500 MHz, so 430 MHz is inside it, and the network has to be cut for that frequency.

Is it a drop in replacement for the 250 W row? No. The difference is 1.67 dB and the packages are not stated to match.

What is the heat load? 139 W at 55 per cent and 92 W at 65 per cent, calculated. Neither number is published and neither replaces a measurement.

How much drive at saturation? Not published. At 15 dB of gain it would be 5.4 W and at 18 dB it would be 2.7 W, so the driver chain depends on a figure the vendor has not given.