HXC40038
Product Specifications
HXC40038
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40038 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40038: twenty five watts at saturation with no compression figure published
The HXC40038 is the largest member of the Hisiwell gallium arsenide internally matched group on 8.5 to 9.6 GHz, and it is the odd one in the ladder. Its index row prints 44 dBm in the saturation column, leaves the 1 dB compression column and the efficiency column empty, and gives a gain of 7 dB. The part is built the same way as the rest of the group, on in-plane matching synthesis with thin film hybrid integration and 50 ohm at both ports, on a 10 V rail with plus or minus 0.8 dB flatness in continuous wave.
44 dBm is 25.12 W. Seven decibels of gain puts the drive at 37 dBm, which is 5.01 W, and that is the single most important number for anyone planning a line up around this part: the stage in front of it is a transmitter in its own right. Without a published efficiency the DC input, the drain current and the dissipation cannot be derived from the data sheet, and any figure printed for those here is an assumption and is labelled as one.
The window is the same 1100 MHz from 8.5 to 9.6 GHz, 12.15 per cent fractional at 9.05 GHz. The gain is one decibel below the three smaller members, which is typical when the periphery grows and the match is synthesised in plane over the same window.
The parameter rows Hisiwell publishes for HXC40038
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 8.5 to 9.6 GHz |
| Bandwidth, calculated | 1100 MHz, 12.15 per cent fractional at a 9.05 GHz centre |
| Saturation output power as published | at least 44 dBm |
| Saturation output power in watts, calculated | 25.12 W |
| Output at 1 dB compression as published | not published, the index prints a slash in that column |
| Gain as published | at least 7 dB |
| Drain efficiency as published | not published, the index prints a slash in that column |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the saturation point, calculated | 37 dBm, 5.01 W |
| DC input if efficiency is 30 per cent, calculated assumption | 83.73 W |
| Drain current if efficiency is 30 per cent, calculated assumption | 8.37 A at 10 V |
| Dissipation if efficiency is 30 per cent, calculated assumption | 58.61 W |
| DC input if efficiency is 40 per cent, calculated assumption | 62.80 W |
| Dissipation if efficiency is 40 per cent, calculated assumption | 37.68 W |
| Output per 100 MHz of the band, calculated | 2.28 W |
| Load voltage at saturation into 50 ohm, calculated | 35.44 V RMS, 50.12 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour at 41 dBm compression on the same window | HXC40037, 30 per cent, 4.20 A |
Why a saturation figure and no efficiency figure is a problem for a buyer
Every other member of this group gives three numbers at one operating point: output at compression, gain, efficiency. This part gives one number at saturation and a gain. The three cannot be combined into a DC input, so the rail current and the heat are unknown from the data sheet, and those are exactly the two figures a chassis and a regulator have to be sized against.
The two rows in the table that carry 30 and 40 per cent are arithmetic on an assumption, not vendor data, and they are marked that way. At 30 per cent the dissipation is 58.61 W; at 40 per cent it is 37.68 W. That is a spread of 21 W on a figure that nobody has published, which tells a buyer more about the state of the documentation than any single number would.
There is a second consequence of an empty efficiency column: the rail current cannot be computed either, so the feed, the connector and the decoupling cannot be sized. The row that carries 8.37 A at 10 V is derived from the 30 per cent assumption, and if the real figure at saturation were 40 per cent the current would be 6.28 A. Hardware should be sized for the higher of the two, and both should be treated as provisional until the factory answers.
The practical route is to ask the factory for the compression point, the efficiency at it, the thermal resistance and any pulse data, and to qualify the first article in the customer laboratory before committing a chassis. Where those figures do not exist, a programme can still use the part, but the thermal margin has to be carried as unknown rather than assumed.
Wide window, high saturation, two stage driver
Twenty five watts on a 1.1 GHz window at 8.5 to 9.6 GHz is a useful combination for a transmitter that has to cover several channels in the low half of X band without a switch, and for a radar front end that needs a saturated output rather than a linear one. The saturation column being the published one is not an accident for that kind of use: a radar or a continuous wave source is often run near saturation where the output is flat and the efficiency is highest.
What the part cannot do without further data is support a linear link budget. If the modulation needs a stated compression point and an adjacent channel figure, this page does not have them, and the 41 dBm member of the same window does. That is the honest split: this part for saturated service, the 41 dBm member for anything that has to stay linear.
The drive requirement is the second constraint. Five watts at 37 dBm can come from the 41 dBm member of this same group, backed off, which keeps the whole line up in one family and one window. That pairing is the one most programmes end up with.
The ladder at 8.5 to 9.6 GHz around HXC40038
The three compression point members step 3.98, 7.94 and 12.59 W, each three decibels apart with a constant eight decibels of gain. This part sits above all three with 25.12 W at saturation, seven decibels of gain and a drive of 5.01 W. In a line up the natural partner is the 41 dBm member as the driver, backed off by several decibels, which keeps both stages on the same window and the same rail.
Against a hypothetical pair of 41 dBm members combined, which would give about 21.5 W for 58.76 W of heat, this part gives 25.12 W from one device. The pair is still the better answer when a failure has to be survived.
The RF power transistor cross reference lists the members of this window with their published rows side by side, and the RF component sourcing page explains what we need from a buyer before quoting a saturated line up.
Questions buyers ask before ordering HXC40038
Is 44 dBm the compression point? No. The index prints it in the saturation column and leaves the compression column empty. Any link budget built on 44 dBm has to treat it as a saturated output and back off for linearity.
What is the efficiency? Not published. The two rows that give a DC input in this table are worked from 30 and 40 per cent assumptions and are labelled as such, and no vendor figure exists to replace them.
Can we get the missing data? We ask the factory for the compression point, the efficiency at it, the thermal resistance and the pulse behaviour. Where a document does not exist, the answer is that it does not exist, and the qualification moves to the customer laboratory.
How do we start? Send the saturated output you need, the duty, the ambient at the base plate and the driver you have. We will confirm the member of the family, quote from the current factory schedule, and ship a sample with the factory test data at the band edges and centre.