HXC40037
Product Specifications
HXC40037
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40037 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40037: twelve and a half watts at the top of the 8.5 to 9.6 GHz compression ladder
The HXC40037 is the highest compression point member of the Hisiwell gallium arsenide internally matched group on 8.5 to 9.6 GHz, at 41 dBm. It uses in-plane matching synthesis and thin film hybrid integration and presents 50 ohm at both ports, so the board sees a matched device across the whole 1.1 GHz window. The published row reads output at 1 dB compression at least 41 dBm, gain at least 8 dB, drain efficiency at least 30 per cent, 10 V drain, plus or minus 0.8 dB flatness, continuous wave, saturation column empty.
41 dBm is 12.59 W. Eight decibels of gain puts the drive at 33 dBm, which is 2.0 W, and that is the figure that decides the driver. At 30 per cent the DC input is 41.97 W, the drain current 4.20 A and the heat 29.38 W. This is no longer a part that runs on a small extrusion; it needs a thermal path with a measured interface and a base plate that spreads heat before it reaches the fins.
The window is 1100 MHz, 12.15 per cent at a 9.05 GHz centre, and the flatness across it is plus or minus 0.8 dB. The gain figure is the same 8 dB as the two smaller members, which is deliberate in a ladder: the drive scales with the output and the interface between stages stays predictable.
The parameter rows Hisiwell publishes for HXC40037
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 8.5 to 9.6 GHz |
| Bandwidth, calculated | 1100 MHz, 12.15 per cent fractional at a 9.05 GHz centre |
| Output at 1 dB compression as published | at least 41 dBm |
| Output at 1 dB compression in watts, calculated | 12.59 W |
| Saturation output power as published | not published, the index prints a slash in that column |
| Gain as published | at least 8 dB |
| Drain efficiency as published | at least 30 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the compression point, calculated | 33 dBm, 2.0 W |
| DC input at compression, calculated | 41.97 W |
| Drain current at compression, calculated | 4.20 A at 10 V |
| Dissipation at compression, calculated | 29.38 W |
| Dissipation if efficiency reaches 40 per cent, calculated | 18.88 W |
| Output per 100 MHz of the band, calculated | 1.14 W |
| Load voltage at compression into 50 ohm, calculated | 25.09 V RMS, 35.48 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour one step below at 39 dBm | HXC40036, 30 per cent, 2.65 A |
| Saturation only member of the same window | HXC40038, 44 dBm, 7 dB gain, efficiency not published |
Twenty nine watts of heat and a two watt driver
Two numbers make this part different from the two below it in the ladder. The first is 29.38 W of dissipation, which is three times the 39 dBm member and four times the 36 dBm one. The second is 2.0 W of drive at 33 dBm, which means the stage in front of it is itself a power amplifier with its own heatsink. A line up built around this part is a two board project, not a one board project.
The rail is 10 V at 4.20 A. That is a buck converter with a four to five amp switch, an inductor rated for the ripple, and a board arrangement that keeps the switching node away from the gate bias line. A linear regulator from any bus above 12 V is out of the question: the drop alone would exceed the amplifier dissipation.
One more point on the driver: if the driver is the 36 dBm member of the same window, it delivers 3.98 W at its own compression, which is three decibels more than the 2.0 W needed here, so it runs three decibels backed off. Backed off, its dissipation falls below the 7.39 W it shows at compression and its gain falls slightly, which is why a level plan should be checked at the band edges rather than at the centre.
The dissipated heat at 40 per cent efficiency would be 18.88 W, which shows how much the number moves with an operating point the vendor does not publish. Nobody should plan a chassis against 18.88 W; the honest planning figure is 29.38 W and a margin above it, because the published efficiency is a minimum at compression and a backed off point will be worse.
The 8.5 to 9.6 GHz window at the top of its power range
At 12.59 W this is a part for a transmitter that has to close a link with a fixed antenna, or for a radar front end that needs the extra few decibels without moving to a larger device on another band. The window covers the low half of X band, including the maritime radar channels near 9.3 to 9.5 GHz and the short haul link allocations that sit at 8.5 to 9 GHz.
Continuous wave operation is stated, so a pulsed application has to be qualified rather than assumed. The dissipation that the part can take in a pulse train depends on the duty cycle and on the thermal mass between the die and the case, and neither figure is published. What is published is the compression point and the efficiency at it, and those hold for the continuous wave condition only.
For a receiver chain the extra power is often wasted, and the 36 dBm member is the better buy. For a transmitter that already has a two watt driver and a chassis with a fin stack, this part is the shortest path to 12.59 W on a window that one part covers without a switch.
The ladder at 8.5 to 9.6 GHz around HXC40037
Read from the bottom, the ladder is 3.98 W, 7.94 W, 12.59 W and then a saturation only 25.12 W device with seven decibels of gain. Each compression point step is three decibels, which is a doubling, and the drive requirement doubles with it because the gain stays at eight. The 44 dBm member breaks that pattern by publishing saturation instead of compression and by giving up a decibel of gain.
Against the 39 dBm member, this part buys 4.65 W for 10.85 W of extra heat and 0.74 W of extra drive. Against the saturation only member, it delivers half the power at a known compression point with a known efficiency, which for many programmes is worth more than the extra three decibels on a figure that is not a compression point at all.
The RF power transistor cross reference sets the members of this window next to each other, and the one stop RF supply page covers how the driver, the final and the passives are bought as one line.
Questions buyers ask before ordering HXC40037
Is 41 dBm available across the whole window? The published figure is a minimum over 8.5 to 9.6 GHz with plus or minus 0.8 dB flatness, so the guarantee is at least 41 dBm everywhere in the window, and the flatness describes the variation around the level plan rather than a separate margin.
What driver do we need? Two watts at 33 dBm, with its own thermal path. Either the 36 dBm member of this same family or a packaged amplifier of the same output will do, and the choice depends on whether the driver has to cover the same window.
How much air do we need? The vendor publishes no thermal resistance, so nobody can answer that from the data sheet. Plan the chassis against 29.38 W at the base plate and measure the case temperature on the first article.
How do we start? Send the output at the antenna, the duty, the ambient, the rail and the space for the heatsink. We will confirm the member of the group, quote from the current factory schedule, and ship a sample with the factory test data at the band edges and centre.