HXC40031
Product Specifications
HXC40031
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40031 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40031: four watts at 40 per cent at 7.7 to 8.5 GHz
The HXC40031 opens the 7.7 to 8.5 GHz group in the Hisiwell gallium arsenide internally matched family, and it is the entry point to the X band part of the range. The window is 799 MHz, 9.88 per cent fractional at an 8.1 GHz centre, and it covers the X band satellite downlink, the 7.9 to 8.4 GHz military tactical allocations and the lower edge of the radar band. The vendor states in-plane matching synthesis and thin film hybrid integration, with 50 ohm at both ports. The index row reads 7.7 to 8.5 GHz, saturation output not printed, output at 1 dB compression at least 36 dBm, gain at least 8 dB, drain efficiency at least 40 per cent, 10 V drain rail, plus or minus 0.8 dB flatness, continuous wave.
36 dBm at compression is 3.98 W. On 10 V the DC input is 9.95 W, the drain current 1.00 A and the heat 5.97 W. The drive is 0.63 W at 28 dBm, one decibel more than the same power on the 6.4 to 7.2 GHz window needs, because the gain falls from 9 dB to 8 dB as the band rises.
The 40 per cent efficiency is the top figure in the family alongside the 6.4 to 7.2 GHz entry part. At 4 W this is a device a small enclosure can cool, which is why it turns up as a driver for the larger X band members and as a final stage in short range links.
The parameter rows Hisiwell publishes for HXC40031
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 7.7 to 8.5 GHz |
| Bandwidth, calculated | 799 MHz, 9.88 per cent fractional at an 8.1 GHz centre |
| Output at 1 dB compression as published | at least 36 dBm |
| Output at 1 dB compression in watts, calculated | 3.98 W |
| Saturation output power as published | not published, the index prints a slash in that column |
| Gain as published | at least 8 dB |
| Drain efficiency as published | at least 40 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the compression point, calculated | 28 dBm, 0.63 W |
| DC input at compression, calculated | 9.95 W |
| Drain current at compression, calculated | 1.00 A at 10 V |
| Dissipation at compression, calculated | 5.97 W |
| Dissipation if efficiency reaches 50 per cent, calculated | 3.98 W |
| Output per 100 MHz of the band, calculated | 0.50 W |
| Load voltage at compression into 50 ohm, calculated | 14.11 V RMS, 19.95 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour one step above at 39 dBm | HXC40032, 35 per cent, 2.27 A |
| Neighbour on the 6.4 to 7.2 GHz window at 36 dBm | HXC40027, 40 per cent, 9 dB gain |
Eight decibels of gain is the number that shapes the line up
At 8 dB the drive requirement is 28 dBm for a 36 dBm output, and that is the figure that decides how many stages sit in front of this part. A single packaged gain block at 30 dBm output covers it with 2 dB of headroom, which is thin but workable. Two stages cost less than a larger driver and give margin for the interstage filter and the connector losses.
The alternative is to run this part backed off and let the next stage do the work. On a 3.98 W device at 40 per cent, backing off 3 dB costs about 2 W of DC input and leaves the efficiency in the low thirties. That is an acceptable trade in a receiver front end where the linearity matters more than the heat.
Efficiency at 40 per cent means 5.97 W of heat for 3.98 W of output. A 1 C per watt plate puts the case 6 degrees above ambient, so the enclosure itself can be the heatsink in most products. That is the practical case where the mechanical team has no room for a liquid loop and the requirement is only a few watts. This is the member to choose when the mechanical team has no room for a cold plate and the requirement is a few watts at X band.
Seven point seven to eight point five gigahertz in a real system
The X band downlink at 7.25 to 7.75 GHz sits just below this window, and the military tactical links at 7.9 to 8.4 GHz sit inside it. In a tactical data link the modulation is often constant envelope and the part runs near compression, so the published 36 dBm and 40 per cent are usable as printed and the only correction is the temperature one.
In a radar front end the requirement is usually pulsed, and this part is specified continuous wave with no pulse rating, no duty cycle figure and no transient thermal impedance curve. A pulsed application is possible at the same average power, but the peak power capability is not documented and has to be measured rather than assumed.
For a satellite downlink the signal is shaped and the linearity requirement is set by the adjacent channel specification. No two tone data is published, so the back off has to come from a measurement on the first article. On a gallium arsenide part at this power the intercept usually sits 8 to 10 dB above compression, which is an expectation and not a specification.
Mismatch at 3.98 W reflects about 0.44 W into the output at a 2 to 1 load. A circulator is good practice but a mismatch at this power is survivable, which is why driver stages at X band are often built without one.
The X band ladder
The 7.7 to 8.5 GHz group runs 36, 39, 41 and 44 dBm, with gain falling from 8 dB to 8 dB to 8 dB to 7 dB across the four. This part is the entry and the natural driver for the 44 dBm member, since 3.98 W of output covers the 5.01 W of drive that the largest member needs only if the interstage loss is kept below 1 dB, which is tight.
Thermally this is the easiest member of the group: 5.97 W at compression fits a 2 mm aluminium base with a thin interface and no airflow, and the case rise stays inside ten degrees. That is why it is the first choice for a driver stage in an enclosure that already carries a larger final device, since the driver adds little to the total heat while giving the final stage its drive.
In practice the 41 dBm member is the better driver for the 44 dBm part, and this one drives the 39 and 41 dBm members. Our RF power transistor cross reference shows the pin compatible options, and the defence grade components page covers the traceability questions that come with the 7.9 to 8.4 GHz allocation.
Questions buyers ask before ordering HXC40031
Does the 8 dB gain hold across the band? The vendor prints at least 8 dB with plus or minus 0.8 dB of flatness, so 7.2 dB at the band edges is the number to carry in a level plan until the first article is measured.
Can it drive the 44 dBm member? Only with a very short interstage path. The larger part needs 5.01 W of drive and this one delivers 3.98 W at compression, so the link has to be under 1 dB of loss and the driver has to be run at compression rather than backed off.
Is it suitable for pulsed radar? The mode column says continuous wave. There is no pulse rating in the vendor material, so a pulsed requirement needs measurement of the transient thermal behaviour before it can be committed.
How do we start? Send the output required, the modulation, the ambient at the base plate and the rail available. We will confirm the family member that fits, quote from the current factory schedule and ship a sample with measured output, gain and efficiency across the band.