HXC40025
Product Specifications
HXC40025
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40025 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40025: twelve and a half watts at 38 per cent on 5.8 to 6.7 GHz
The HXC40025 is a gallium arsenide internally matched power transistor from Hisiwell on a 900 MHz window from 5.8 to 6.7 GHz. That window covers the commercial C band uplink at 5.925 to 6.425 GHz and the upper fixed service channels that sit above it. The vendor states in-plane matching synthesis and thin film hybrid integration, with 50 ohm at both ports. The index row reads 5.8 to 6.7 GHz, saturation output not printed, output at 1 dB compression at least 41 dBm, gain at least 10 dB, drain efficiency at least 38 per cent, 10 V drain rail, plus or minus 0.8 dB flatness, continuous wave.
41 dBm at compression is 12.59 W. What separates this part from the rest of the 5.8 to 6.7 GHz group is the pair of figures beside the power: 38 per cent and 10 dB at the same time. On 10 V the DC input is 33.13 W, the drain current 3.31 A and the heat 20.54 W. The 1.26 W of drive at 31 dBm is inside the reach of a small packaged amplifier, so the line up stays at two stages.
Bandwidth is 900 MHz, 14.40 per cent fractional at a 6.25 GHz centre. Apart from the 1.6 to 1.7 GHz member that is the widest window in the family, which means one part covers a channel plan with several sub bands without touching the match. The plus or minus 0.8 dB is a whole band figure and it is the one a level plan should carry.
The parameter rows Hisiwell publishes for HXC40025
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 5.8 to 6.7 GHz |
| Bandwidth, calculated | 900 MHz, 14.40 per cent fractional at a 6.25 GHz centre |
| Output at 1 dB compression as published | at least 41 dBm |
| Output at 1 dB compression in watts, calculated | 12.59 W |
| Saturation output power as published | not published, the index prints a slash in that column |
| Gain as published | at least 10 dB |
| Drain efficiency as published | at least 38 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the compression point, calculated | 31 dBm, 1.26 W |
| DC input at compression, calculated | 33.13 W |
| Drain current at compression, calculated | 3.31 A at 10 V |
| Dissipation at compression, calculated | 20.54 W |
| Dissipation if efficiency reaches 50 per cent, calculated | 12.59 W |
| Output per 100 MHz of the band, calculated | 1.40 W |
| Load voltage at compression into 50 ohm, calculated | 25.09 V RMS, 35.48 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour on the same window at 45 dBm | HXC40026, 35 per cent, 9.04 A |
| Neighbour one step below at 39 dBm | HXC40024, 35 per cent |
Thirty eight per cent at twelve and a half watts
Efficiency decides whether a transmitter fits the box it has been given. At 38 per cent, 12.59 W of radio frequency costs 33.13 W of DC input and leaves 20.54 W as heat. A part at 30 per cent would need 41.97 W of DC input for the same output and would leave 29.38 W in the same footprint. Between those two cases sits the difference between a finned heatsink and a cold plate, and between a steady case temperature and a thermal run away that only shows after twenty minutes of key down.
The vendor figure is quoted at compression, and the qualification matters. Back the part off six decibels for a multicarrier signal and the efficiency falls into the twenties, because the drain current does not fall in step with the drive. A transmitter specified from the published number alone runs hot in the backed off condition, which is where most fielded equipment actually sits. Budget the thermal path from the backed off figure, not from the compression figure.
The 3.31 A drain current sets the feed. A wide track with vias at both ends, or two parallel bond wires, is usual at this level, and the choke has to carry 3.31 A without saturating at the peak of the modulation envelope. From 3 A upward the inductance between the converter and the drain also stops being a detail: at 6 GHz it is a real impedance, and the decoupling has to sit within a few millimetres of the drain pad.
Five point eight to six point seven gigahertz in a real system
The lower half of this window is the commercial C band satellite uplink, where the ground terminal has to close the link against rain fade and the transmit power is the only lever left after the antenna is fixed. The upper half, 6.4 to 6.7 GHz, carries fixed service point to point links and the upper channels of the same satellite bands. A 900 MHz match lets one board serve both, which is why this part turns up in ground terminals built for more than one operator.
In an uplink the signal is shaped and the satellite operator sets the power spectral density, so the operating point is deliberately backed off from compression. That puts the burden on linearity rather than on output. Hisiwell publishes no two tone data, no third order intercept and no adjacent channel figure, so none of that is quoted here. On a gallium arsenide part of this class the intercept usually sits 8 to 10 dB above compression, but that is an expectation and not a specification. A two tone measurement on the first article settles it before a production order.
For load mismatch, an internally matched part at 50 ohm is more forgiving than a discrete die with an external network, but it is not immune. At 12.59 W a 2 to 1 mismatch reflects about 1.4 W back into the output, which the die has to absorb on top of its own dissipation. A circulator with a terminated load is the standard answer and in an uplink terminal that has to survive an antenna fault it is not optional.
Temperature is the other open number. The table gives no thermal resistance and no derating curve, so the safe method is to measure the case temperature on the first article at full drive, then hold the base plate below 70 C and carry a decibel of output margin. At 20.54 W of dissipation a 1 C per watt path puts the junction 20 degrees above the case, which is the order of magnitude to plan with until the vendor supplies the real figure.
The ladder at 5.8 to 6.7 GHz
Four members share this window: 36, 39, 41 and 45 dBm at compression, all on 10 V with 10 dB of gain. This part and the HXC40026 are the only ones above 39 dBm, and the step between them is 4 dB, which is a factor of 2.5 in power and a jump in drain current from 3.31 A to 9.04 A. Most transmitters put a driver and this part in series rather than jumping to the 45 dBm member, because the 3.16 W of drive the larger part needs has to come from somewhere with its own thermal path.
Compared with the 39 dBm member, this part buys two decibels of output and three points of efficiency for the same 10 V rail, and it keeps 10 dB of gain rather than trading it away. That combination is usually worth the extra current when the antenna is fixed and the link budget is short. Our RF component sourcing page lists the questions we ask before quoting a line up of this shape, and the RF power transistor cross reference shows the step from one member to the next on the same window.
Questions buyers ask before ordering HXC40025
Is the efficiency quoted at saturation? No. The published row is at 1 dB compression and the saturation column carries a slash for this part. Expect a lower figure at a backed off operating point and a higher one near saturation.
Can it run from a 12 V bus? Not directly. The drain rail in the vendor table is 10 V, and at 3.31 A the drop across a linear regulator is 6.6 W of extra heat. A buck converter set to 10 V is the usual answer.
What is the flatness worth in a two stage line up? The plus or minus 0.8 dB is a band edge figure for one stage. Two stages inherit the sum unless the driver is flatter, so a fixed level plan should carry about 1.2 dB for the pair.
How do we start? Send the output at the antenna, the modulation, the ambient at the base plate and the rail available. We will confirm which member of the family fits, quote from the current factory schedule and ship a sample with measured output, gain and efficiency across the band.