HXC40024
Product Specifications
HXC40024
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40024 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40024: eight watts on 5.8 to 6.7 GHz for the C band uplink
The HXC40024 is the second member of the gallium arsenide internally matched family on the 5.8 to 6.7 GHz window. The vendor states in-plane matching synthesis and thin film hybrid integration, with 50 ohm at both ports. The index row reads 5.8 to 6.7 GHz, saturation output not printed, output at 1 dB compression at least 39 dBm, gain at least 10 dB, drain efficiency at least 35 per cent, 10 V drain rail, plus or minus 0.8 dB flatness, continuous wave.
39 dBm is 7.94 W, which is 1.6 W above the standard 6 W solid state uplink module and well inside the range a single carrier satellite terminal needs after the antenna gain is counted. The window is 900 MHz, 14.40 per cent fractional at 6.25 GHz, so one part covers the standard C band uplink and the extended transmit band together.
The efficiency is 35 per cent against the 40 per cent of the smaller member on the same window. That is the usual pattern in this family and it is worth planning for: the larger die in a wider match gives up efficiency for output, and the heat at compression goes from 5.97 W to 14.75 W.
The parameter rows Hisiwell publishes for HXC40024
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 5.8 to 6.7 GHz |
| Bandwidth, calculated | 900 MHz, 14.40 per cent fractional at a 6.25 GHz centre |
| Output at 1 dB compression as published | at least 39 dBm |
| Output at 1 dB compression in watts, calculated | 7.94 W |
| Saturation output power as published | not published, the index prints a slash in that column |
| Gain as published | at least 10 dB |
| Drain efficiency as published | at least 35 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the compression point, calculated | 29 dBm, 0.79 W |
| DC input at compression, calculated | 22.70 W |
| Drain current at compression, calculated | 2.27 A at 10 V |
| Dissipation at compression, calculated | 14.75 W |
| Dissipation if efficiency reaches 50 per cent, calculated | 7.94 W |
| Output per 100 MHz of the band, calculated | 0.88 W |
| Load voltage at compression into 50 ohm, calculated | 19.93 V RMS, 28.18 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour on the same band at 36 dBm | HXC40023, 40 per cent efficiency |
| Neighbour on the same band at 41 dBm | HXC40025, 38 per cent efficiency |
Eight watts at the flange of an outdoor unit
An outdoor satellite unit is a sealed box with a metal wall and no fan, and the radio frequency stage sits on that wall. 7.94 W of output with 14.75 W of heat is the kind of load a cast housing can carry by conduction if the interface between the flange and the wall is thin and if the wall has enough area. A 2 mm thick aluminium wall with 200 square centimetres of area and a natural convection coefficient of 5 W per square metre per kelvin dissipates about 10 W at 20 C above ambient, which is short of the requirement, so the housing is usually larger than the board.
At 2.27 A the drain feed can be a track, and the converter can be a single phase part with a current limit above 3 A. That combination keeps the power supply inside the same box and on the same board, which is what a terminal builder wants: one assembly, one connector, one test station.
The 0.79 W of drive is at the upper end of what a packaged gain block can deliver, so the driver is usually a small transistor. If the whole terminal is this family, the driver is the 36 dBm member run at 29 dBm, which gives a matched pair on one rail and one bias arrangement.
Linearity is the constraint that decides the operating point. A single carrier uplink can run near compression, but a multi carrier uplink needs back off, and the intermodulation products fall into the adjacent transponder. At 6 dB back off the part delivers about 2 W and the efficiency falls to the low twenties, which is the case that sizes the housing rather than the compression figure.
Six gigahertz in the open air
The 5.8 to 6.7 GHz window is where C band satellite uplinks live, and it is also used by point to point links over moderate distances and by radars that need a wide instantaneous bandwidth. Rain attenuation at 6 GHz is modest compared with the Ku band, which is the reason C band remains in service for links that have to stay up in bad weather.
For a satellite terminal the antenna gain and the path loss are fixed by the operator, so the amplifier's job is to deliver a stable level across the transponder's band with a predictable compression point. A part with plus or minus 0.8 dB flatness over 900 MHz needs little equalisation, which is a real saving in a terminal that would otherwise carry a slope network.
For a point to point link the modulation may be high order and the linearity requirement is tighter. The same part is then run further back, and the system gain comes from a larger antenna rather than from the amplifier. That is a system choice made before the part is selected, and it is the first question we ask when a customer sends a specification for this band.
The step below and the step above
The HXC40023 at 36 dBm and 40 per cent is the smaller neighbour, and the HXC40025 at 41 dBm and 38 per cent is the larger. This part sits between them with the lowest efficiency of the three, which is worth knowing when a product is thermally tight: the 41 dBm device run at 39 dBm draws slightly less current than this part at its compression point and has two decibels of margin.
Above 41 dBm the family goes to 45 dBm on the same rail, which is the step that requires a cold plate. For an outdoor unit the 45 dBm member is rarely the right answer because the housing cannot carry 58.73 W by natural convection, and the practical ceiling for a passive housing is around the 41 dBm member.
Our one stop RF supply page describes how we quote a mounted assembly with the carrier and the interface, which is how most outdoor units are built, and our RF component sourcing page covers the device on its own.
Questions buyers ask before ordering HXC40024
Does the part cover 5.925 to 6.425 GHz with margin? Yes. Both edges sit inside the 5.8 to 6.7 GHz window, and the plus or minus 0.8 dB flatness applies across the whole window rather than only at the centre.
Can it run at 8 W continuously in a sealed box? At compression, no. The 14.75 W of heat needs a housing with enough area, and a sealed box at 50 C ambient will run the flange hotter than a bench test suggests.
What is the input return loss? Not published. The vendor states 50 ohm at both ports but gives no return loss figure, so a first article has to be measured if the driver is sensitive to load pull.
How do we start? Send the uplink band, the carriers and their spacing, the ambient at the housing and the rail. We will confirm the fit, quote from the current schedule and ship a sample measured at 5.8, 6.25 and 6.7 GHz with the compression point at each.