HXC40012
Product Specifications
HXC40012
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40012 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40012: eight watts at compression on 4.4 to 5.0 GHz from a 10 V rail
The HXC40012 is a gallium arsenide internally matched power transistor from Hisiwell covering 4.4 to 5.0 GHz. The vendor states that it uses in-plane matching synthesis and thin film hybrid integration, and the product page adds that both ports sit at 50 ohm. The index row reads 4.4 to 5 GHz, saturation output not printed, output at 1 dB compression at least 39 dBm, gain at least 10 dB, drain efficiency at least 35 per cent, 10 V drain rail, plus or minus 0.8 dB flatness, continuous wave.
39 dBm at compression is 7.94 W. The saturation column carries a slash for this part, so the only published power number is a linear one. That matters more on gallium arsenide than on gallium nitride, because the compression point is where the gain has already given up a decibel and the saturation figure would sit above it with the efficiency falling away. A buyer who needs 8 W of clean output at the antenna is reading the right number. A buyer who needs 8 W at saturation is not, and should allow for a part one step up the ladder.
The window is 600 MHz wide, 12.77 per cent fractional at a 4.7 GHz centre. For an internally matched transistor that is a wide match, and the plus or minus 0.8 dB flatness is the vendor figure that goes with it. Wide matching is bought at some loss in gain and in efficiency against a narrow tuned stage, and the trade is usually worth taking when one part has to cover several channel plans or several customers on the same line.
The parameter rows Hisiwell publishes for HXC40012
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 4.4 to 5.0 GHz |
| Bandwidth, calculated | 600 MHz, 12.77 per cent fractional at a 4.7 GHz centre |
| Output at 1 dB compression as published | at least 39 dBm |
| Output at 1 dB compression in watts, calculated | 7.94 W |
| Saturation output power as published | not published, the index prints a slash in that column |
| Gain as published | at least 10 dB |
| Drain efficiency as published | at least 35 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the compression point, calculated | 29 dBm, 0.79 W |
| DC input at compression, calculated | 22.70 W |
| Drain current at compression, calculated | 2.27 A at 10 V |
| Dissipation at compression, calculated | 14.75 W |
| Dissipation if efficiency reaches 50 per cent, calculated | 7.94 W |
| Output per 100 MHz of the band, calculated | 1.32 W |
| Load voltage at compression into 50 ohm, calculated | 19.93 V RMS, 28.18 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour on the same band at 45 dBm compression | HXC40014, 10 dB gain, 35 per cent |
The drive port at 29 dBm
Ten decibels of gain is the lowest figure in this family, and it decides the shape of the line up behind the part. To reach 7.94 W out, the stage in front has to deliver 0.79 W, which is 29 dBm. That is a real driver, not a gain block, and it is the reason a two stage line built around this transistor needs both stages to have a proper thermal path rather than only the output device.
Low gain also keeps the input match forgiving. At 10 dB, a 1.5 to 1 input return loss costs about 0.17 dB of the drive reaching the die, which a system with any margin absorbs. Parts with 20 dB or more of gain demand a pad or an isolator in front to stay stable, and the same instability shows up as a shift in the match as the drive rises. This part does not carry that risk, which is one reason it appears in transmitters that are tuned once and then left alone.
The 2.27 A at 10 V is the other half of the same story. A drain feed that drops a tenth of a volt at 2.27 A loses two per cent of the DC power, which is small, but a feed that drops half a volt loses ten per cent and also lets the drain voltage sag on the modulation peaks. On a 10 V rail the headroom is thin, so the choke, the track width and the number of vias under the source pads all have to be sized for the current rather than copied from a 1 A stage elsewhere on the board.
Heat is 14.75 W at the compression point. On a carrier with 2 C per watt the case rise is 30 C above the base plate, which is workable with a modest heatsink and a fan, and it is not workable in a sealed box at 70 C ambient without one. The vendor publishes no thermal resistance, so the first article has to be the measurement.
Where 4.4 to 5.0 GHz is used
The window sits between the standard C band satellite downlink that ends at 4.2 GHz and the unlicensed 5 GHz wireless allocations that begin at 5.15 GHz. Inside it are the extended C band receive windows used on some satellite payloads, the 4.9 GHz public safety band in the United States, several fixed wireless and point to point allocations, and a number of military data links and telemetry channels that were placed there precisely because the commercial traffic is sparse.
For a satellite receive chain the requirement is usually linearity rather than raw power, because the signal carries a shaped modulation and the system budget has no room for compression. A part that is rated at 39 dBm at compression runs at 33 to 35 dBm for a clean multicarrier signal, and the efficiency falls to somewhere near 25 per cent at that back off. The published 35 per cent belongs to the compression point and should not be carried into a link budget for a backed off application.
For a data link or a telemetry transmitter the modulation is often constant envelope, and the part can run at or near compression where the published figures apply. That is the case this transistor is specified for, and it is also the case in which the 35 per cent efficiency and the 14.75 W of heat are the numbers to use.
One property of a 50 ohm internally matched part is worth stating plainly. A first article can be measured with two connectors, a bias tee and a power meter, without a tuned fixture. That shortens the route from sample to decision, and it is the practical reason to accept the matching loss against a discrete transistor with a hand tuned output network. Our guide to choosing an RF amplifier sets out that sequence, rail first and match second.
Choosing between the four power levels on this band
The same 4.4 to 5.0 GHz window carries four members in this family. The HXC40011 delivers 36 dBm at compression with 40 per cent efficiency, the HXC40012 delivers 39 dBm at 35 per cent, the HXC40013 delivers 41 dBm at 38 per cent, and the HXC40014 delivers 45 dBm at 35 per cent. All four run on 10 V, all four quote plus or minus 0.8 dB flatness, and all four are continuous wave parts. The choice between them is made by the output the antenna needs and by the drive that is already available, not by the band.
The step from 36 to 39 dBm doubles the output and doubles the current, from about 1 A to 2.27 A. The step from 39 to 41 dBm is two decibels, which is a modest change in a system budget and a large change in the drive requirement, from 0.79 W to 1.26 W. The step to 45 dBm is another four decibels and takes the current to 9 A, at which point the supply and the thermal path dominate the whole discussion.
Where the output need sits between two members, the usual answer is the smaller part backed off rather than the larger part throttled. A 41 dBm device run at 39 dBm delivers the same power with better linearity, and the price difference is often smaller than the cost of the extra driver that the larger part would need. Our RF power transistor cross reference lays the family out side by side when a part has to be placed against a competitor number.
Questions buyers ask before ordering HXC40012
Is 39 dBm a saturation figure? No, it is 1 dB compression. The saturation column carries a slash. If a system needs a saturation number, it has to be measured on the first article, and the result is normally half a decibel to a decibel above the compression figure.
Is there a data sheet? Not in the usual sense. The vendor publishes an index row and a product page that repeats five parameters, the 50 ohm port impedance and the matching technique. There are no curves, no scattering parameters, no thermal resistance and no bias point in the published material.
What has to be on the purchase order? The band, the 10 V rail, the continuous wave condition and the quantity. No orderable addendum, marking code or packing column is published, so reel size and moisture level come from the factory quotation rather than from a catalogue.
How do we start? Send the band, the output point that matters, the drive available and the rail. We will check the fit against this part and its three neighbours on the same window, quote against the current factory schedule, and ship a sample with output at compression and gain measured at both band edges.