HX514500V
Product Specifications
HX514500V
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HX514500V from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HX514500V: a 500 W row whose gain and efficiency columns are printed the wrong way round
The HX514500V appears on the Hisiwell 50 V shelf listing at 0.96 to 1.4 GHz, 500 W, pulse mode, with 60 in the gain column and 17 in the efficiency column. Read literally, that is a part with 60 dB of gain and 17 per cent efficiency, which no gallium nitride transistor in this class has. Swapping the two columns gives 17 dB of gain and 60 per cent efficiency, which is exactly what a 500 W L-band pulse part looks like.
The product page behind the row adds a second problem. The address linked from the row is titled HXN50337, and its text describes a 500 W internally matched HEMT for commercial pulsed amplifier use from 960 to 1400 MHz. So the catalogue entry and the vendor page describe the same power and the same band under two different part numbers, and the row does not say whether HX514500V is an older code for the same device, a customer specific variant, or a mis-linked entry.
Both points are worth writing down before a quotation, because the arithmetic of the part changes with each. At 17 dB of gain the drive needed for 500 W is 39.99 dBm, which is 10.0 W; at 60 dB it would be a few milliwatts, which would make the part a driver rather than a final stage. At 60 per cent efficiency the DC input is 833 W and the heat is 333 W; at 17 per cent the DC input would be 2941 W and the heat 2441 W, which no package of this size can move.
The HX514500V rows as the vendor publishes them
| Part class | Gallium nitride HEMT, internally matched, commercial pulsed amplifier use |
| Frequency range, index row | 0.96 to 1.4 GHz |
| Frequency range, product page | 960 to 1400 MHz |
| Band width, calculated | 440 MHz |
| Band ratio, calculated | 1.46 to 1 |
| Output power, both documents | 500 W |
| Output in dBm, calculated | 56.99 dBm |
| Gain column as printed on the row | 60 |
| Efficiency column as printed on the row | 17 |
| Gain after the columns are swapped, per the physics | 17 dB |
| Efficiency after the swap | 60 per cent |
| Drive needed at 17 dB, calculated | 39.99 dBm, 10.0 W |
| Drive needed if 60 dB were taken literally | A few milliwatts, which no final stage of this size uses |
| DC input at 60 per cent, calculated | 833 W, 16.7 A on a 50 V rail, 333 W of heat |
| DC input at 17 per cent, calculated | 2941 W, 58.8 A, 2441 W of heat, which the body cannot move |
| Drain rail, index row | 50 V |
| Load voltage at 500 W into 50 ohm, calculated | 158.1 V RMS, 223.6 V peak |
| Peak swing against the rail, calculated | 4.47 times |
| Mode, index row | Pulse |
| Pulse width and duty | Not published on either document |
| Part number on the linked product page | HXN50337, not HX514500V |
| Package and body | Not published |
| Thermal resistance, junction to case | Not published |
| Load impedance at the output | Not published, no load pull table |
| Orderable addendum and packing | None published under either number |
Two part numbers, one device, and what a buyer should do about it
The first move is to ask the vendor which number is current. A 500 W L-band pulse part with the same band, the same power and the same rail appearing under two codes is a normal situation when a part is carried over from an earlier catalogue, and it is also what a mis-linked table looks like. A written answer settles which string belongs on a purchase order.
The second move is not to build a quotation on the printed gain and efficiency until the columns are confirmed. A 60 dB gain figure on a 500 W part would change the driver architecture completely and would be wrong in a way that only appears on the bench. A 17 dB figure fits the device class, the power and the band, and it is the one to plan with.
The third move is to treat the band as 960 to 1400 MHz and not as 0.96 to 1.4 GHz in the loose sense. A 440 MHz window at L band is a wide ask for one match, and the vendor's own page describes the part as internally matched for that window, which is the strongest single statement on the record. Anything outside it is unsupported by both documents.
What 333 W of heat means in a pulse part
At 60 per cent efficiency and 500 W of output the die dissipates 333 W while the pulse is on. The steady state thermal resistance would have to be very low to move that on a continuous carrier, which is why the mode is pulse. With the duty unpublished, the average dissipation cannot be calculated, and the heat sink cannot be sized from the page.
What the page does allow is the voltage. At 500 W into 50 ohm the load sees 223.6 V peak, which is 4.47 times the 50 V rail, so the output network, the connector and any circulator in front of the antenna have to be rated well above the DC rail. This is the number that decides whether a standard connector is adequate and whether a directional coupler can be placed after the stage.
The current side is equally clear at 60 per cent: 16.7 A average on the 50 V rail, with a peak that is higher still because the drain current follows the envelope. A feed sized for 17 A of average current will droop on the crest, and a drooping rail on a pulse amplifier shows up as a chirp on the leading edge of the pulse.
Where the row sits, and which neighbour to compare it with
The natural comparison is the HXN50154 at 800 W on 960 to 1200 MHz and the HXN50152 at 350 W on 960 to 1400 MHz. The three rows trade the same two variables: this one holds the wide 440 MHz window at 500 W, the 800 W part narrows to 240 MHz, and the 350 W part holds the wide window at a lower power and adds a 400 W narrow band rating.
A buyer who needs the full 960 to 1400 MHz span and 500 W has this row. A buyer who needs 800 W inside 960 to 1200 MHz has the HXN50154. A buyer who needs the wide span at a lower power, or 400 W inside 60 MHz, has the HXN50152. The three are not interchangeable and the differences are in the band and the drive, not only in the watts.
That comparison, with the drive figure for each, is on the RF power transistor cross reference page. Where the enquiry is still at the stage of a band and a power, the RF component sourcing desk will confirm which of the three numbers is current before a price is issued.
Questions buyers ask about the HX514500V
Is this the same part as HXN50337? The row links to a page titled HXN50337 with the same power, band and mode. Whether the two are the same device under two codes, or the row is mis-linked, is a question for the vendor, and it should be asked in writing before a purchase order carries either string.
Is the gain really 60 dB? Almost certainly not. 60 dB belongs to a driver or a receive amplifier, not to a 500 W final stage, and 17 dB is what a part of this class shows. The two columns on the row appear to be transposed, and the transposition should be confirmed rather than assumed.
What pulse condition applies? Neither document states a width, a duty or a peak figure. The mode is pulse and the power is a pulse figure without a condition, which means the factory has to supply one before the thermal path can be sized.
How is it bought? Through a channel that can prove the batch and confirm the current part string, with an incoming check at 960 to 1400 MHz and a pulse test at the agreed condition. The one stop RF supply page covers how the driver, the circulator and the passives are consolidated around it so that one schedule covers the whole chain.