Contact Us

HX5060140P2

Brand: Hisiwell
Hisiwell HX5060140P2 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HX5060140P2 — Discrete & Power Semiconductors | Superb Automation

HX5060140P2

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HX5060140P2 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HX5060140P2: one hundred and forty watts at 5 to 6 GHz with eleven decibels of gain

The HX5060140P2 is the largest continuous wave part on the 5 to 6 GHz shelf from Hisiwell, on a 28 V rail, with 140 W of saturation, 11 dB of power gain and 50 per cent drain efficiency. One hundred and forty watts is 51.46 dBm by calculation. It is the complete datasheet in a group where three of its neighbours publish a power row and nothing else.

Eleven decibels of gain at 140 W is the figure that shapes the whole amplifier. The drive at saturation is 11.1 W, which is 40.46 dBm. That is a power stage in its own right: a two stage line up where the second stage is itself a 10 W part, with its own sink and its own bias. A 140 W stage is never a single transistor on a board, it is a chain with three thermal problems.

Fifty per cent efficiency at 140 W means the drain takes 280 W and the part leaves 140 W of heat. That is the number that decides the package: a 140 W dissipation needs a flange on a liquid cooled plate or a very large forced air sink, and no board level copper spreader carries it in continuous wave.

The band is 1 GHz from 5 to 6 GHz, 18.2 per cent fractional, and the part is unmatched, so the network is built on the customer board. At 140 W the match is not only a match, it is also the current path: the circulating current in the first section is several times the load current.

At 50 ohm the output is 83.7 V RMS and 118.3 V peak. A two to one mismatch takes the peak to 167.4 V, which puts the capacitors at 250 V and the match inductors at a current rating that matches the mismatch case rather than the matched one.

The parameter rows behind the HX5060140P2

Part classGallium nitride HEMT power transistor, unmatched
Frequency range5 to 6 GHz
Band width, calculated1,000 MHz
Fractional bandwidth at 5.5 GHz centre, calculated18.2 per cent
Saturation output, index row140 W
Saturation in dBm, calculated51.46 dBm
Power gain11 dB
Gain as a ratio, calculated12.6 times
Drive at saturation, calculated11.12 W, 40.46 dBm
Drain efficiency50 per cent
DC input at 50 per cent, calculated280 W
Drain current, calculated10.0 A at 28 V
Heat at saturation, calculated140 W
Heat per watt of output, calculated1.0 W of heat for every watt delivered
Drain rail28 V
ModeContinuous wave
Load voltage at 50 ohm, calculated83.7 V RMS, 118.3 V peak
Load voltage under a two to one mismatch, calculated167.4 V peak
Load voltage at 12.5 ohm, calculated41.8 V RMS, 59.2 V peak
Output per gigahertz of band, calculated140 W per GHz
MatchingUnmatched, network on the customer board
Package and bodyNot published on the index row
Thermal resistance, junction to caseNot published
Compression pointNot published
Gain flatness over the bandNot published

Two hundred and eighty watts in and one hundred and forty out

The supply is a 300 W module at 10 A with headroom for the crest of a modulated carrier, and the feed is a copper bar rather than a trace. At 10 A continuous a 300 mil trace at one ounce copper runs warm, and a 2 ounce trace is the normal choice at this current.

The heat is symmetric with the output, which is rare and convenient: for every watt delivered the part leaves one watt behind. A 140 W amplifier is a 280 W heater with a 140 W antenna attached, and the thermal path has to be planned as a 140 W continuous load from the first drawing.

The drive chain is the second thermal system. Eleven watts of drive from a 28 V line up means a driver that is itself dissipating 10 to 15 W, and that driver sits on the same board, often on the same sink. The two loads add and the sink is sized on the sum.

The voltage at the output is the third constraint. One hundred and eighteen volts peak in the matched case and 167 V under mismatch is beyond the usual 100 V ceramic, so the network is built with 250 V parts. That is a cost item that a 50 W stage does not carry.

HX5060140P2 against the other 5 GHz parts

HX5060140P25 to 6 GHz140 W saturation11 dB50 per centReference point
HXN502225 to 6 GHz140 W peakNot publishedNot publishedSame output, pulse mode, no gain or efficiency
HX446050F24.4 to 6 GHz50 W saturation15 dB55 per cent4.47 dB less output, 4 dB more gain
HX446030F24.4 to 6 GHz30 W saturation14 dB55 per cent6.69 dB less output, 3 dB more gain
HXN502175 to 6 GHz100 W peakNot publishedNot published1.46 dB less output, no gain or efficiency
HX5141K00VPDC to 1 GHz900 W per side16 dB57 per centDifferent band, more than six times the output

Against the pulse member with the same output the trade is one row of information. The pulse part publishes nothing beyond the peak figure, and this part publishes gain and efficiency, which is what makes a continuous system plannable. The 11 dB also tells the buyer that the drive is 11 W, a figure that a pulse part would hide until a sample arrived.

Against the 50 W wideband part the difference is 4.47 dB of output for 4 dB of gain. In practice that means this part needs a 10 W driver and the 50 W part needs a 1.6 W driver, so the system level comparison is not 140 against 50, it is two amplifiers with two different line ups.

The whole 5 GHz family is on RF power transistor cross reference, and the way a 140 W stage is put together with its driver and passives is on one stop RF supply.

Board notes for a one hundred and forty watt continuous stage

The first item is the thermal path. One hundred and forty watts continuous is a flange on a liquid plate or a very large forced air sink, and the flange flatness and the interface are specified, not assumed.

The second item is the driver. Eleven watts of drive is a second amplifier on the same board with its own heat, and the two are budgeted together from the start.

The third item is the capacitor rating. At 118 V peak matched and 167 V under mismatch, 250 V ceramics and inductors rated for the mismatch current are the minimum.

The fourth item is the current path. At 10 A the feed is a bar or a 2 ounce trace, the choke is rated above 15 A for the crest and the ground return is as wide as the feed.

Questions buyers ask about HX5060140P2

Is 140 W continuous? The row is a saturation figure with a continuous wave mode, so 140 W is the intended continuous output at saturation. A backed off point runs cooler and lasts longer.

How much drive does it need? 11.12 W at 11 dB of gain, which is 40.46 dBm. That is a driver stage in its own right.

How much heat? One hundred and forty watts at 50 per cent efficiency, exactly one watt of heat per watt of output.

Can it be pulsed at higher output? The mode row reads continuous wave and the part is already at 140 W, so a pulse application is a different part number rather than a different bias point.

How do we start? Send the band, the output at the connector, the signal, the ambient and the rail. We will quote from the schedule and ship a sample with gain, efficiency and the flange temperature measured at 5.0, 5.5 and 6.0 GHz.