Contact Us

HX280018H

Brand: Hisiwell
Hisiwell HX280018H is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HX280018H — Discrete & Power Semiconductors | Superb Automation

HX280018H

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HX280018H from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HX280018H: ten watts to eight gigahertz on 28 V

The HX280018H is an unmatched gallium nitride HEMT from Hisiwell and the middle member of the three small parts at the top of the 28 V shelf. The family index prints DC to 8 GHz, 10 W of saturation output and 28 V, and leaves the gain, the efficiency and the average power columns blank. The mode column reads 7GHz, the same note the 4 W member carries. No data sheet is linked and no per part page resolves for this row.

Ten watts is 40.00 dBm exactly, which is a round number and therefore a convenient one in a level plan. The step from the 4 W member is 3.98 dB, and the step up to the 20 W member is a further 3.01 dB, so the three parts form a near perfect three decibel ladder.

Everything that decides a purchase beyond the power is unpublished. Gain, efficiency, package, bias point, thermal resistance and mode are all missing from the row, and the honest position is that this page can size the part but cannot specify the board around it.

The HX280018H row and the columns it leaves empty

Part classUnmatched gallium nitride HEMT
Frequency rangeDC to 8 GHz
Saturation output10 W
Saturation output in dBm, calculated40.00 dBm
Power gainNot published, slash in the index column
Drain efficiencyNot published, slash in the index column
Average power columnNot published, slash in the index column
Drive power at saturationCannot be calculated without a gain figure
DC input at 40 per cent efficiency, calculated25.0 W, 0.89 A, 15.0 W of heat
DC input at 45 per cent efficiency, calculated22.2 W, 0.79 A, 12.2 W of heat
DC input at 50 per cent efficiency, calculated20.0 W, 0.71 A, 10.0 W of heat
DC input at 55 per cent efficiency, calculated18.2 W, 0.65 A, 8.2 W of heat
Drain rail28 V
Mode column in the index7GHz, a frequency note rather than a mode
PackageNot printed for this row
MatchingUnmatched, external network on the customer board
Load voltage at 50 ohm, calculated22.4 V RMS, 31.6 V peak
Thermal resistance, junction to caseNot published
Gate bias point and quiescent currentNot published
Operating and storage temperatureNot published
Orderable addendum, marking and packingNot published
Data sheetNot linked from the product page
Family siblingsHX280R48HS at 4 W, HX280028H at 20 W
Nearest part in another seriesHXN50264, 10 W, DC to 8 GHz

Ten watts is a supply question before it is a thermal one

The current at 10 W depends entirely on an efficiency that is not published. At 40 per cent the drain draws 0.89 A and the heat is 15 W; at 55 per cent it draws 0.65 A and the heat is 8.2 W. The difference between those two cases is nearly double the supply and nearly double the heat, and neither is a rounding error.

That is why the first question to the factory is the efficiency at the intended band edge. A part quoted at 10 W with an unknown efficiency is a part whose heatsink is unknown, and a heatsink chosen on the optimistic case will run hot in the field.

The voltage side is easy. Ten watts into 50 ohm is 22.4 V RMS and 31.6 V peak, which is inside the 50 V class of capacitor and inside the rating of ordinary connectors. That is the one electrical number on this page that can be used without a factory answer.

The supply is a 1.5 A converter in the worst case and under an amp in the best, so the board can be built to the pessimistic figure and left unchanged when the real efficiency arrives.

Ten watts at forty decibels is also a convenient building block in a combiner: four of them in phase give forty six decibels, which is sixty four watts from parts that each need under an amp and under a hundred milliwatts of drive. That is a common route to a higher power wideband amplifier when a single flanged part would not cover the band. The combining loss of a four way network is around 0.5 to 0.8 dB, so the arithmetic that looks like six decibels usually delivers about five point three, and a buyer should count that loss before choosing the number of parts.

The three step ladder to eight gigahertz

HX280R48HS4 W36.02 dBmMMS five by four3.98 dB below this part
HX280018H10 W40.00 dBmNot printedReference point
HX280028H20 W43.01 dBmNot printed3.01 dB above this part
HXN5026410 W40.00 dBmBare die family rowSame power, other series
HX2040185F185 W, 2 to 4 GHz52.67 dBmFlanged12.67 dB above, band stops at 4 GHz

The ladder is exactly three decibels between the ten and twenty watt members, and four decibels from four to ten. That consistency suggests one die scaled across three periphery sizes rather than three unrelated parts, which is the normal pattern in a gallium nitride catalogue.

Against the large flanged parts the difference is the band, not just the power. The 185 W member covers 2 to 4 GHz and is 12.67 dB above this one; this part covers to 8 GHz at a tenth of the supply current. A wideband instrument or an EMC amplifier picks the small part for the band and accepts the power.

The RF power transistor cross reference lists all three members with the dB step between them, and the one stop RF supply page covers how a wideband amplifier chain is bought.

Board notes while the gain is unknown

Without a gain figure the driver cannot be sized. The practical route is to build the first article with a driver that covers 10 to 20 dB of gain, measure the part, and then remove the excess attenuation. That is slower than a data sheet but it is what the documents force.

The gate bias is unpublished, so the negative rail is adjustable and clamped, and the quiescent point is set on the article. A gallium nitride HEMT with no published bias window is a part where the sequencer is part of the test fixture on the first build.

The match covers eight gigahertz, which puts the package parasitic inside the network. Since the package is not even printed for this row, the first step is a photograph of the sample and a footprint from the factory rather than a guess.

The heat is between 8 and 15 W depending on the efficiency, so the spreader is sized for the pessimistic case. A part quoted at 10 W that turns out to run at 40 per cent needs a heatsink twice the size of the one chosen at 55 per cent.

Questions buyers ask about HX280018H

What is the gain? Not published. The index prints a slash in that column and there is no per part page or data sheet to fall back on.

What is the package? Also not printed for this row. The 4 W member next to it is an MMS five by four, and the 10 W and 20 W rows do not say. Ask before the footprint is drawn.

Is it continuous wave? The mode column reads 7GHz, which is a frequency note, so the mode is unconfirmed. Do not commit it to a pulse budget without a written answer.

Is it the same die as HXN50264? Both rows print 10 W and DC to 8 GHz and the documents do not say. It is a fair question for the factory and it decides whether the two are interchangeable in a bill of materials.

How do we start? Send the band, the output, the drive available and the ambient. We will get the gain, the package and the mode confirmed, quote from the factory schedule, and ship a sample for a bench measurement.