UM1441ARQZ
Product Specifications
UM1441ARQZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The UM1441ARQZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADuM1441ARQZ: quad micropower digital isolator in a 16-lead QSOP
The ADuM1441ARQZ is a four channel digital isolator built for quiescent current rather than for speed, in the 16-lead QSOP package, rated minus 40 C to 125 C. At 3.3 V each channel draws 5.6 uA with the refresh oscillator enabled and 0.3 uA with it disabled, plus 148 uA per Mbps of actual data, so an idle isolated interface costs microamps rather than milliamps. The part is aimed at battery powered instruments, isolated sensor interfaces and any board where an isolated SPI or GPIO link has to stay alive while the rest of the system sleeps.
Published values
| Parameter | Value |
|---|---|
| Channels | Four, bidirectional communication supported |
| Data rate | Up to 2 Mbps, non return to zero |
| Quiescent current, 3.3 V | 5.6 uA per channel with refresh, 0.3 uA without |
| Dynamic current, 3.3 V | 148 uA per Mbps per channel |
| Quiescent current, 2.5 V | 3.1 uA per channel with refresh, 0.1 uA without |
| Dynamic current, 2.5 V | 117 uA per Mbps per channel |
| Pulse width distortion | Below 8 ns |
| Common mode transient immunity | Above 25 kV per microsecond |
| Isolation, this package | 2500 V RMS for one minute per UL 1577, working voltage 565 V peak |
| Other approvals | IEC/CSA 60950-1, VDE 0884-17, intrinsic safety certificates |
| Temperature range | Minus 40 C to 125 C |
| Package | 16-lead QSOP, RQ-16 |
The refresh oscillator is the whole decision
An inductive isolator carries data as edges, so a channel that sees no edges for a long time has no way to prove it is still alive. The refresh oscillator sends a periodic pulse so a stuck input can be distinguished from a constant one. It costs about 5.3 uA per channel at 3.3 V, which is nearly twenty times the disabled figure, and it is the difference between a link that is guaranteed to report the right DC level after a long idle and one that is only guaranteed while edges keep arriving. In a system that polls a sensor every second the refresh is unnecessary and the quiescent current falls by a factor of eighteen. In a system that takes a switch closure as an interrupt the refresh is mandatory, because the switch can sit in one state for days.
What the 16-lead body does not include
The 16-lead QSOP carries 2500 V RMS of isolation and a 565 V peak working voltage. The 20-lead SSOP version of the same family carries 3750 V RMS, a 645 V peak working voltage, and medical approvals that the QSOP does not have. Both are in the same datasheet, so a buyer who reads the features page and assumes one isolation figure applies to every order code will be wrong by a factor of 1.5. Reinforced isolation ratings also differ from basic ratings, and the safety table has to be read per package rather than per part family. This is the single most common mistake when this family is bought as a drop in for another isolator.
Where the current actually goes
The dynamic term of 148 uA per Mbps per channel dominates as soon as the interface is busy. A 2 Mbps link on four channels is 4 times 2 times 148 uA, which is 1.2 mA, against 22 uA idle. A 100 kbps link on two channels is 30 uA. That is why the family suits low rate isolated interfaces such as a slow SPI bus, a UART or a set of GPIOs, and why it is the wrong choice for an isolated USB or an isolated high speed ADC bus where an isolator with a higher dynamic efficiency is the correct part. The 2 Mbps ceiling is a hard limit rather than a typical figure.
Sourcing isolators without a footprint change
Grade, channel direction and package all change the order code in this family, and the direction count differs across the suffixes, so the pin configuration has to be checked per code before a substitution is proposed. The cross reference work sits on the ADI part second source page, the difference between a true drop in and a footprint change is on pin to pin cross reference, and a file that needs the isolators consolidated with the rest of the buy is described on one stop BOM sourcing.