REF198GSZ-REEL
Product Specifications
REF198GSZ-REEL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The REF198GSZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
REF198GSZ-REEL: A 4.096 V Reference That Drops 100 mV, and the 73 Codes of Error Over Temperature
The REF198GSZ-REEL is a 4.096 V precision band gap reference in an 8-lead SO package. Initial accuracy is plus or minus 2 mV maximum, temperature coefficient is 5 ppm per degree Celsius maximum, supply current is 45 uA maximum and 15 uA in sleep mode through the SLEEP pin, load regulation is 4 ppm per mA and line regulation 4 ppm per V, output current is 30 mA with short circuit protection, and the dropout is low enough that a supply 100 mV above the output is enough to hold regulation. The series is specified over minus 40 to plus 85 degrees Celsius with typical performance quoted to plus 125 degrees. All electrical grades are available in the SO-8, while the PDIP and TSSOP bodies carry only the lowest grade.
4.096 V is not a round number by accident. It is the reference that makes a 12-bit converter's step exactly 1 mV and a 16-bit converter's step 62.5 uV, so the scaling from codes to volts is a shift rather than a multiplication. That is why a 4.096 V part sits next to most 12 and 16-bit data converters.
2 mV of initial error is 32 codes; 5 ppm per degree Celsius over 125 degrees adds 41 more
One 16-bit step at 4.096 V is 62.5 uV, so the plus or minus 2 mV initial accuracy is 32 codes each way. The temperature coefficient of 5 ppm per degree Celsius over a 125 degree span is 625 ppm, which is 2.56 mV or 41 codes. Added together the reference can move 4.56 mV, which is 73 codes, over the temperature range. A system that specifies 16-bit absolute accuracy and ignores the reference is specifying a converter accuracy and not a measurement accuracy.
The load regulation is the third term. At 4 ppm per mA and 30 mA of output the reference moves 120 ppm, which is 491.5 uV or about 8 codes, so a converter that draws a varying current from the reference will modulate the full scale. The usual answer is a buffer between the reference and a switched capacitor load, and the 30 mA output is there to make that buffer unnecessary in slow converters.
100 mV of dropout means a 5 V rail can feed it and a 4.096 V rail cannot
The minimum supply is 4.196 V. A 5 V rail at minus 5 percent is 4.75 V, which leaves 554 mV of headroom and is comfortable. A 4.096 V rail, however stable, has no headroom at all, so a board that regulates to exactly the reference voltage cannot power its own reference. That is a wiring decision made early, and it is the reason the reference often runs from the analogue 5 V rail rather than from a dedicated low noise regulator at the same voltage.
Sleep mode at 15 uA is 131 mAh over a year if it is left on permanently, which is far below the self discharge of any cell the instrument would use. The SLEEP pin takes a TTL or CMOS low level, so a processor that is itself in standby can hold the reference off with a pin that is guaranteed low rather than floating.
| Function | 4.096 V precision band gap voltage reference |
| Initial accuracy | Plus or minus 2 mV maximum, which is 32 codes at 16 bits |
| Temperature coefficient | 5 ppm per degree Celsius maximum, 2.56 mV or 41 codes over 125 degrees |
| Total error | About 4.56 mV, 73 codes at 16 bits, over the temperature range |
| Load regulation | 4 ppm per mA, 491.5 uV at the 30 mA output rating |
| Line regulation | 4 ppm per V |
| Supply current | 45 uA maximum, 15 uA in sleep mode |
| Dropout | 100 mV above the output, minimum supply 4.196 V |
| Output current | 30 mA with short circuit protection |
| Package | 8-lead SO, order code GSZ-REEL |
| Lifecycle | In production at the vendor |
Two questions buyers ask
Is the G grade the tightest grade in the family?
No. The family page quotes the plus or minus 2 mV and 5 ppm figures at series level, and the grade letters select from a table where the tighter grades carry a higher price. The order code has to be matched to the grade column of the data sheet for the accuracy actually being bought, and the PDIP and TSSOP bodies only carry the lowest grade, so a through hole build cannot have the best tolerance.
Can the reference drive a 16-bit converter directly?
It can drive the reference pin, and the converter's own reference input current is what matters. A successive approximation converter draws a charge packet on every conversion, and the 4 ppm per mA figure turns that into a small modulation. With a 30 mA output and 4 ppm per mA the reference is stiff enough for most converters, and a 0.1 uF to 1 uF capacitor at the reference pin is the part that supplies the charge packet rather than the reference.
Ordering and supply
The GSZ suffix is the SO-8 body with the reel, and the PBF suffix is the lead free finish. The family covers 2.5 V, 3.0 V, 4.096 V and 5.0 V outputs in the same body, and the output voltage is not interchanged by a resistor, so the order code has to carry the right voltage.
We hold this reference for instrumentation and converter builds. The analog mixed signal ICs page lists the references we carry, ADC and DAC cross reference is where a converter and its reference are compared as a pair, and where a card is being re-sourced, pin to pin cross reference is the place to check whether another reference drops into the same footprint.
Request Quote — In Stock, 100% New & Original, Full Warranty