OP2177ARZ
Product Specifications
OP2177ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The OP2177ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
OP2177ARZ dual precision amplifier: two channels of the same die
The OP2177ARZ is the dual member of the OP1177 family in an 8 lead SOIC. It carries the same 60 microvolt maximum offset, 0.7 microvolts per degree C drift and 120 dB rejection figures as the single, on a 400 microamp per amplifier budget, with a plus and minus 2.5 V to plus and minus 15 V supply window.
Published values
| Parameter | Value |
|---|---|
| Channels | two |
| Package | 8 lead SOIC_N |
| Offset voltage | 60 microvolts maximum |
| Offset drift | 0.7 microvolts per degree C maximum |
| Input bias current | 2 nanoamperes maximum |
| Voltage noise | 8 nanovolts per root hertz typical |
| Supply current | 400 microamps per amplifier |
| Supply range | plus and minus 2.5 V to plus and minus 15 V |
| Temperature range | minus 40 to plus 125 degrees C |
Two channels, one thermal path
A dual in an 8 lead body puts both amplifiers on one die with one junction temperature. The 400 microamp figure is per amplifier, so the pair draws 800 microamps, and the dissipation on a plus and minus 15 V rail is about 24 milliwatts shared between the two channels.
That sharing matters when one channel drives a load and the other sits at zero. The loaded channel heats the die and the idle channel's offset moves with it, at 0.7 microvolts per degree C. A pair used as a matched instrumentation stage therefore sees a small thermal mismatch whenever the two channels are working at different levels.
Using the pair as an instrumentation stage
Two matched precision amplifiers plus three resistors make a difference amplifier, and the 120 dB common mode rejection of each channel is what allows the resistor tolerance to be the limiting error rather than the amplifier. A 0.1 percent resistor pair gives about 54 dB of rejection, so the amplifier's 120 dB is not the constraint.
The 2 nanoampere bias current limits the source impedance the pair can see: 100 kilohms gives 200 microvolts, three times the offset. Above that figure the bias term, not the offset, sets the accuracy, and a picoampere part becomes the better choice.
Supply window and headroom
A plus and minus 2.5 V floor means the part runs on a plus and minus 2.5 V rail with only a volt of headroom to the plus and minus 1.5 V signal that a 3 V converter can accept. The plus and minus 15 V ceiling covers the classic instrument rail without a second order code.
The output is not rail-to-rail on this family, so the swing has to be read from the specifications at the actual load. Where the full rail is needed, the OP777 single and the OP484 quad are the rail-to-rail members.
Ordering and replacements
The pages that answer this most often are the amplifier cross reference for the family alternatives, how to verify a drop in replacement for the acceptance test, and vendor consolidation for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Are the two channels of the OP2177 independent? They are separate amplifiers with separate inputs and outputs, sharing one supply pair and one die. Matching between them is not specified as a parameter, so a circuit that depends on the two channels tracking has to measure it rather than assume it.
What is the difference between the OP2177 and the OP1177? Channel count and package only. The single is an 8 lead part with one amplifier, the dual puts two in the same 8 lead outline, and the electrical limits are the same across the family. The current and the thermal figures are what change with the channel count.