ADG1634BRUZ-REEL7
Product Specifications
ADG1634BRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1634BRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG1634BRUZ-REEL7: four changeover switches at 4.5 ohm in a 20 lead TSSOP
What this order code is
ADG1634BRUZ-REEL7 is the four channel single pole double throw member of the ADG1633 and ADG1634 family, an industrial CMOS switch in a 20 lead TSSOP on a reel. Each of the four channels connects a common pin to one of two throws, and the channels switch independently. On resistance is 4.5 ohm typical with 1 ohm of flatness across the signal swing, which is the pair of numbers that makes a switch usable as a gain setting element rather than only as a router.
The supplies are unusually wide for a switch of this resistance: plus or minus 3.3 V to plus or minus 8 V on a dual rail, or 3.3 V to 16 V on a single rail, with no separate logic supply pin. Logic inputs are 3 V compatible, so a 3.3 V controller drives the part directly even when the analog rails are plus or minus 5 V or a single 12 V.
Parameters as published
| Item | Value |
|---|---|
| Configuration | 4 independent SPDT |
| On resistance | 4.5 ohm typical |
| On resistance flatness | 1 ohm |
| Continuous current | up to 206 mA per channel |
| Dual supply | plus or minus 3.3 V to plus or minus 8 V |
| Single supply | 3.3 V to 16 V |
| Logic supply | none required |
| Logic threshold | 3 V compatible |
| Signal range | rail to rail |
| Switching action | break before make |
| Enable pin | fitted on the LFCSP version only |
| Bodies in the family | 20 lead TSSOP and 4 mm by 4 mm LFCSP |
| Known good die | ADG1634-KGD, guaranteed to data sheet limits |
| Packing | reel |
Numbers that decide the application
The 4.5 ohm typical and 1 ohm flatness have to be read together. Twenty two percent variation in channel resistance across the swing is what produces even order distortion when a signal passes through the switch, so a part with 4.5 ohm fixed would be cleaner than a part that moves between 4.5 and 5.5 ohm. Into a 1 kohm load the absolute value is 0.45 percent of gain, which is 18 codes of a 12 bit converter, and it is the flatness rather than the absolute value that shows up in a distortion measurement.
206 mA per channel against 4.5 ohm is 0.93 V of drop and 191 mW of dissipation in the switch at the limit. Four channels all at that current would be 764 mW in a 20 lead TSSOP, which is beyond what the body can dissipate, so 206 mA is a rating per channel and not an operating point for all four at once. At a realistic 20 mA per channel the drop is 90 mV and the total dissipation is 72 mW, which is comfortable.
The missing enable pin on this body is the detail that decides whether the code is right. The vendor puts the EN pin on the LFCSP version of the four channel part, so a board that needs to open all channels under firmware control has to use the LFCSP body and not this TSSOP. Where the channels are only ever switched between two positions and never floated, this code is the simpler and cheaper choice.
Where it fits and where it does not
It fits gain switching in data acquisition, filter selection, audio and video routing, relay replacement, medical systems and battery powered instruments, and it is one of the few switches in this resistance class that runs from a single 12 V rail without a logic supply. It does not fit a path that needs the channels to be disabled together, because this body has no enable pin. It does not fit a fault exposed input, where the protected multiplexers in the same catalogue are the right part, and it does not fit a differential pair as a substitute for a real differential switch, because two channels of one part share a substrate and not a timing guarantee.
Supply and second source questions
The questions that come back on this code are about the missing enable pin, the current rating and the body. The current rating is per channel, the enable is a body dependent feature, and the 4 mm by 4 mm LFCSP is not a drop in for the TSSOP even though the die is the same. Parts that hold 4.5 ohm and rail to rail operation across the same supply window and parts that need a separate logic rail are separated on the medical device component page.
Sourcing notes and next step
We quote this code against the bill of materials and check the fields that decide whether the reel is usable: channel configuration, body, enable requirement and packing. A line that says ADG1634 without the body suffix can arrive as the LFCSP, which does not fit a TSSOP footprint, and the known good die version is a separate code for a different assembly route. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability, and where the exact code is short we will say so rather than substitute a body that changes the pinout. The wider switch and multiplexer list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty