ADG636YRUZ-REEL7
Product Specifications
ADG636YRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG636YRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG636YRUZ-REEL7: a dual SPDT switch with 1 pC of charge injection for sample and hold work
What this order code is
ADG636YRUZ-REEL7 is a dual single pole double throw CMOS switch in a 14-lead TSSOP on a reel. Each of the two switches connects a common pin to one of two throws, and each is selected independently, so the part can route two signals at once or build a changeover pair. It runs from a dual supply of plus or minus 2.7 V to plus or minus 5.5 V, or from a single supply of 2.7 V to 5.5 V, and it is specified over the automotive range of minus 40 C to plus 125 C. The RU string is the TSSOP body and REEL7 is the reel.
The number that defines this part is charge injection: 1 pC typical, and plus or minus 1.5 pC over the full signal range. When a switch turns off, the charge stored in its channel is dumped into whatever node it was connected to, and on a sample and hold capacitor that charge becomes a voltage step. A part with 20 pC of injection cannot hold an accurate sample on a small capacitor, and a part with 1 pC can. The other published figures support the same role: 10 pA of leakage typical and 100 pA maximum at 25 C, 85 ohm typical on resistance matched to within 2 ohm between the two switches, and break before make action.
Parameters as published
| Item | Value |
|---|---|
| Configuration | dual SPDT, independent control |
| Charge injection, typical | 1 pC |
| Charge injection over signal range | plus or minus 1.5 pC |
| Leakage, typical at 25 C | 10 pA |
| Leakage, maximum at 25 C | 100 pA |
| On resistance, typical | 85 ohm |
| On resistance match | within 2 ohm between switches |
| Dual supply | plus or minus 2.7 V to plus or minus 5.5 V |
| Single supply | 2.7 V to 5.5 V |
| Signal range | rail to rail |
| Switching action | break before make |
| Body | 14-lead TSSOP |
| Temperature range | minus 40 C to plus 125 C |
Numbers that decide the application
One picocoulomb into a 100 pF hold capacitor is 10 mV. On a 5 V full scale that is 131 least significant bits of a 16-bit converter, and the 1.5 pC worst case is 15 mV or 197 bits. Into a 1 nF capacitor the same charge is 1 mV, so the size of the hold capacitor is a direct trade against the injection error, and the 1 pC figure is what makes a 100 pF hold capacitor usable at all. This is the calculation that decides whether a switch belongs in a precision front end, and it is why the injection figure is quoted over the signal range rather than at one input level.
Eighty five ohms of on resistance is large for a signal path but small compared with the load it is meant to drive. Into a 1 kohm load it is 7.83 percent of the total, and the 2 ohm match between the two switches is 2.35 percent of the resistance, so a changeover between the two throws produces a 2.35 percent amplitude step. A circuit that has to change over without a visible step needs the load impedance to be much larger than 85 ohm, which is the usual case in front of a buffer.
Leakage of 100 pA maximum into a 1 Mohm source is 0.1 mV and into 10 Mohm it is 1 mV, so the part holds a high impedance node only up to a point. The 10 pA typical figure is two decades better than the guarantee and is the one that describes a room temperature board, while the maximum is what a qualification test uses. On a board that runs at 125 C the leakage is far above both figures, and a hold time that is acceptable at 25 C has to be rechecked at the top of the range.
Where it fits and where it does not
It fits sample and hold circuits, automatic test equipment, data acquisition, audio and video routing, relay replacement, battery powered instruments and avionics, which is the list the vendor publishes. It does not fit a power path because of the 85 ohm, and it does not fit a multiplexed converter front end that needs eight channels, which is the ADG658. A circuit that needs a single switch in a tiny body is also better served by a smaller part, since this one is a dual in a 14-lead body.
Supply and second source questions
The questions that come back on this code are about injection, leakage over temperature and the supply arrangement. A replacement with the same footprint and the same on resistance can still differ by a factor of ten in charge injection, and that difference only appears as an offset step in a sampled system. The parts that share the function and the ones that only look similar are separated on the ADI part second source page.
Sourcing notes and next step
We quote this code against the bill of materials and check the configuration, the supply arrangement, the body, the temperature grade and the packing. Where the exact code is short we will say so rather than offer a switch with a larger injection figure and let the sample accuracy move. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability. The broader part list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty