ADG3304BRUZ-REEL7
Product Specifications
ADG3304BRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG3304BRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG3304BRUZ-REEL7: four bidirectional level translations with no direction pin to get wrong
What this order code is
ADG3304BRUZ-REEL7 is a four channel bidirectional logic level translator in a 14 lead TSSOP on a reel, specified from 1.15 V to 5.5 V. One side is powered from VCCA and the other from VCCY, and a signal presented on either side appears translated on the other without a direction control pin. The requirement that goes with it is that VCCA must always be lower than VCCY, so the low voltage side is fixed by the wiring and not by the signal direction.
An EN pin puts both sides into a high impedance state and is referenced to VCCA, which is what allows the part to sit on a bus that has to be released when the board is in standby. The family is qualified for automotive applications, and a separate EP version to the AQEC standard covers defence and aerospace use over minus 55 to plus 125 degrees C, which is a different order code and not something this suffix carries.
Parameters as published
| Item | Value |
|---|---|
| Channels | 4, bidirectional |
| Direction control | none required |
| Supply range, both sides | 1.15 V to 5.5 V |
| Ordering rule | VCCA lower than VCCY |
| Quiescent current | below 1 uA |
| Enable | EN referenced to VCCA, three state on both sides |
| Automotive qualification | yes, this family |
| Defence and aerospace | ADG3304-EP, AQEC, minus 55 to plus 125 C |
| Typical use in the vendor text | SPI and MICROWIRE between a low voltage controller and a higher voltage device |
| Body | 14 lead TSSOP on this code, WLCSP and 20 lead LFCSP in the family |
| Packing | reel |
Numbers that decide the application
The quiescent current below 1 uA is the figure that makes this part usable on a permanently powered rail. At 3.3 V it is 3.3 uW, which over a year is 8.8 mAh, small enough that the translator can stay enabled while the rest of the board sleeps. It is a quiescent figure and not a switching figure: the current during a transition comes from the charge needed to move the load capacitance at the chosen rate, and the vendor page does not publish a maximum data rate for this suffix, so the speed has to come from the full data sheet rather than from an assumption.
The absence of a direction pin removes a whole class of failure. A translator with a direction pin needs the controller to know, before it drives the line, which end is talking; when firmware gets that wrong the two ends drive against each other and the symptom appears as random bit errors under load. This part senses direction from the logic levels themselves, which works because the two supplies are ordered and the drivers on each side are strong enough to overcome the opposite side's hold. The cost is that it expects push pull signals: an open drain bus that only pulls low has no high level for the sensing to act on, and that case needs a different approach.
The VCCA lower than VCCY rule is the one that gets broken during a board review. A board that runs 3.3 V on the controller side and 1.8 V on the peripheral side cannot use this part with those two rails the way they are; the low rail has to be VCCA. Where a product has to work with the rails the other way round, the answer is two parts with the rails swapped or a translator family that does not impose the ordering.
Where it fits and where it does not
It fits SPI and MICROWIRE links between a low voltage controller and a higher voltage peripheral, smart card readers, portable instruments and any board where four or fewer signals cross a rail boundary. Four channels covers a four wire SPI bus exactly, and the fifth signal, usually a chip select or an interrupt, is the point at which the eight channel part in the same family is needed instead. It does not fit a bus above 5.5 V, it does not fit an open drain bus, and it does not fit a safety critical path that needs a defined state during power sequencing, because a translator with no direction pin also has no way to report which side it thinks is driving.
Supply and second source questions
The questions that come back on this code are about the rail ordering, the channel count and the package. The rail ordering is a wiring rule and not a preference: reverse it and the part does not translate. The channel count is fixed at four on this code, and a fifth signal means a different part rather than a spare channel. The other translator families that hold up over the same rail range and the ones that stop at 3.6 V are separated on the MCU cross reference page.
Sourcing notes and next step
We quote this code against the bill of materials and check the four fields that decide whether the reel is the right one: channel count, body, qualification and packing. The automotive qualified version and the AQEC version are different order codes from this one, and a line that asks for the part by family name alone does not say which of them is needed. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability, and where the exact code is short we will say so rather than move the line to a package that does not fit. The wider interface and logic list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty