Contact Us

MAX809TEUR+T

Brand: Analog Devices
Analog Devices MAX809TEUR+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX809TEUR+T — Analog & Mixed-Signal ICs | Superb Automation

MAX809TEUR+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX809TEUR+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX809TEUR+T: 3.08 V Is Not 3.0 V, and a 3.3 V Rail Is the Wrong Place for It

The MAX809TEUR+T is the T threshold option of the MAX809 three-pin reset circuit from Analog Devices, in the 3-pin SOT23 package on tape and reel. The family monitors a supply and holds the reset output asserted for at least 140 ms after the rail has risen back above the trip point. The published table gives a 3.08 V nominal threshold for the T suffix, 12 uA of typical supply current for the family, a 140 ms minimum and 560 ms maximum reset timeout, 20 us from the rail dropping 100 mV below the threshold to the reset asserting, a push-pull active-low output, and a guaranteed valid output state down to a 1 V rail.

The threshold window is four times wider than the headline

The T suffix is usually read as 3.08 V and quoted as a 1.5 percent part. The electrical table says otherwise once temperature is included. At 25 C the window is 3.04 V to 3.11 V, which is plus or minus 1.14 percent. Over -40 C to +85 C it opens to 3.00 V to 3.15 V, plus or minus 2.5 percent. Over the full -40 C to +125 C range of the SOT23 option it is 2.92 V to 3.23 V, plus or minus 5.0 percent, a spread of 310 mV. The 30 ppm per C tempco on a 3.08 V threshold is 92 uV per C, so the widening comes from the initial window plus drift, not from drift alone.

Put that window against a real rail. A 3.3 V supply at its minus five percent limit sits at 3.135 V. The 3.00 V to 3.15 V window means some units have already tripped at that point and some have not, so a legal 3.3 V rail can hold a processor in reset depending on which unit was fitted. The T option belongs on a 3.0 V rail, where minus five percent is 2.85 V, 70 mV below the lowest threshold in the window and therefore a guaranteed trip. A 3.3 V rail wants the S option at 2.93 V, and a 2.5 V rail wants the Z option at 2.32 V.

140 ms minimum and 560 ms maximum are one orderable number

The reset timeout is published as 140 ms minimum, 240 ms typical and 560 ms maximum. A processor whose boot sequence needs 300 ms of reset hold time is therefore inside the specification for one unit and outside it for another, because the guarantee is the 140 ms floor. The 560 ms ceiling is the other half of the problem: a board that debounces a power switch by waiting for reset to release has to assume the slow end, otherwise a slow unit releases into a rail that has not finished rising.

The 20 us delay from a rail 100 mV below threshold to the reset asserting is the number that decides whether the processor stops before its core voltage collapses. On a rail falling at 100 V per second, 100 mV takes 1 ms, so the reset is already 1 ms late relative to the moment the rail passed the threshold. The guaranteed valid state down to 1 V covers the logic level of the output, not the timing of the core.

ParameterPublished valueWhat it decides
Threshold, T option3.08 V nominalA 3.0 V rail part, not a 3.3 V rail part
Window at 25 C3.04 V to 3.11 VPlus or minus 1.14 percent
Window, -40 C to +85 C3.00 V to 3.15 VPlus or minus 2.5 percent
Window, -40 C to +125 C2.92 V to 3.23 V310 mV of spread, plus or minus 5.0 percent
Threshold tempco30 ppm per C92 uV per C, secondary to the initial window
Reset timeout140 ms min, 240 ms typ, 560 ms maxGuarantee is the floor, not the typical
Rail to reset delay20 us at 100 mV below threshold1 ms late on a 100 V per second fall
Supply current17 uA typical, 50 uA maximum in SOT23Always-on supervisory budget

What changes with the package and the output stage

The SOT23 option is rated to +105 C and the SC70 option to +125 C, and the threshold windows differ slightly between them, so a quotation that moves package without moving the electrical table has moved the trip point. The push-pull output drives the reset line in both directions, which is right for a single processor and wrong for two devices sharing one reset net, where an open-drain MAX803 and one pull-up is the correct arrangement.

Questions buyers ask before they order this part number

Can the T suffix replace an S suffix on an existing 3.3 V board? No. The T window reaches 3.15 V and a 3.3 V rail at minus five percent is 3.135 V, so the substitution puts the trip point inside the normal operating range. The S suffix at 2.93 V is the one that leaves margin on a 3.3 V rail.

Is 12 uA the current to use in a battery budget? The 12 uA figure is the family summary. The SOT23 table gives 17 uA typical and 50 uA maximum for the T, S, R and Z options at up to 3.6 V, and 100 uA above +85 C, so an always-on supervisory chain of three devices has to be counted at the maximum.

The part sits in the analog and mixed-signal IC category. Buyers comparing supervisory options usually open power management cross reference first, and projects that start from a shortage of an existing monitor use BOM shortage recovery instead.

Request Quote — In Stock, 100% New & Original, Full Warranty