Contact Us

AD8210YRZ

Brand: Analog Devices
Analog Devices AD8210YRZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8210YRZ — Analog & Mixed-Signal ICs | Superb Automation

AD8210YRZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8210YRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8210YRZ: A 100 mV Shunt Already Uses 2 V of the 5 V Output at a Gain of 20

The AD8210 is a high-side current sense amplifier with a fixed gain of 20 V/V, a single 5 V supply and two reference pins that set where the zero current level sits. Because the gain is fixed in silicon, the shunt voltage a board can use is bounded by the output swing rather than by the amplifier: 100 mV of shunt drop is 2 V at the output, 250 mV is the full 5 V, and anything above that clips. Boards that report a current reading which flattens near full load have usually sized the shunt for 200 mV or 250 mV at rated current and left no room for tolerance, temperature or a load transient.

The reference pins decide the measuring window

VREF1 and VREF2 are not spare pins. Tied to ground, the output runs from 0 V upwards and the part measures current in one direction only. Tied to mid supply, the output sits at 2.5 V at zero current and swings either way, which is what an H-bridge or a bidirectional battery path needs. The two wirings give the same amplifier but half the usable range each way, so the shunt has to be chosen after the reference wiring, not before it.

Shunt drop at full loadOutput at gain of 20What is left for headroom
50 mV1.0 VPlenty, and the resolution per bit is the cost
100 mV2.0 VUnidirectional use with tolerance room
125 mV2.5 VBidirectional use centred on mid supply
250 mV5.0 VNothing; saturation starts at rated current

The common-mode range is why the part exists

The common-mode sweeps published for the AD8210 run from about minus 2 V to plus 65 V while the amplifier itself runs from a 5 V rail, so a shunt sitting on a 12 V, 24 V or 48 V rail is inside the part. That is the whole point of a dedicated high-side amplifier: the signal of interest is a few tens of millivolts riding on a rail that would destroy a normal op amp input. Below ground matters too, since an inductive load that kicks the rail negative on turn-off must not take the sense amplifier with it.

Common-mode steps, not offset, limit the useful bandwidth

The data sheet publishes common-mode step recovery error plots that run up to several hundred millivolts of output error, and input step rise and fall times in the 60 ns to 690 ns range depending on amplitude. A motor bridge or a high-side switch moves its node by tens of volts in a hundred nanoseconds, and the amplifier output needs time to return to a valid reading afterwards. Two things follow for a real board: a differential RC filter across the two inputs is the intended way to slow the step down, and the converter should sample after the blanking window rather than during it. Supply current for the whole amplifier is quoted at 4.5 mA, so the filter resistors can be in the hundreds of ohms without loading anything.

Getting the code right when the shunt changes

The gain of 20 is fixed, so a reworked board that needs more resolution has to lower the shunt and accept a smaller signal, and the offset and drift of the amplifier then become the floor. When a board is being reworked and the original code is short, the substitution question is the reference wiring, the gain and the common-mode class, in that order. The amplifier cross reference page covers the current sense family, the pin to pin cross reference page covers footprint compatibility, and incoming lot checks follow the incoming inspection plan.