HMC472ALP4E
Product Specifications
HMC472ALP4E
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC472ALP4E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC472A: Positive Control, 0.5 dB Steps and 54 dBm of Input Intercept Below 3.8 GHz
The HMC472A is a six bit digital attenuator covering dc to 3.8 GHz with 0.5 dB steps to 31.5 dB, a single +5 V supply and TTL and CMOS compatible control. Its insertion loss is 1.4 dB typical below 1.5 GHz, its input third order intercept is +54 dBm and its typical step error is 0.25 dB. It is the narrowband member of the family, and the narrow band is what buys those numbers: a part specified to 3.8 GHz can hold a 20 dB return loss and a quarter dB step accuracy that a part specified to 33 GHz cannot.
What the narrow band buys
| Parameter | Value | Compare with the wideband parts |
|---|---|---|
| Frequency range | dc to 3.8 GHz | A third of the range, with better accuracy |
| Insertion loss dc to 1.5 GHz | 1.4 dB typical, 1.8 dB maximum | Roughly half the loss of a 13 GHz part |
| Return loss | 20 dB in all states | Twice as good in dB terms as the wideband family |
| Step error | 0.25 dB typical | Half the step error of the 13 GHz part |
| Input intercept | +54 dBm typical | 11 dB more than the 13 GHz part |
| Control and supply | Six lines at 0 V or +5 V, single +5 V rail | No negative rail and no translator |
Single supply and positive logic remove the whole level shifting problem
The control interface is the same shape as a microcontroller port: six lines, 0 V or +5 V, with thresholds that a 3.3 V driver can meet. There is no negative rail, no translator and no sequencing rule, which is why this part is often chosen for a first prototype and kept for production. The penalty is at the top of the band, where the part simply stops: 3.8 GHz is below the 5 GHz band, so it cannot serve a 5 GHz radio no matter how much attenuation accuracy is wanted.
Near dc operation needs the off chip capacitors
The attenuator requires off chip ac ground capacitors to work near dc, and without them the low end of the band rolls off. Those capacitors are part of the circuit, not optional bypass: they set the point at which the internal ac ground stops being an ac ground, and the value moves that point down in frequency. A board that copies the reference pattern but omits the two capacitors will measure 1 to 2 dB more loss at 100 MHz and no difference at 1 GHz, which is a difficult fault to chase without the data sheet in hand.
Where 54 dBm of intercept changes a system
An input intercept of +54 dBm means the attenuator can sit directly after a driver stage without contributing intermodulation, which is exactly where a gain control element is most useful in a transmitter chain. A part with +40 dBm in the same position would generate products at the level of the wanted signal after only a few dB of back off, and the usual fix, moving the attenuator ahead of the driver, changes the noise contribution at the low end of the gain range.
Ordering and replacement
Order codes in this family differ in packing and lead finish, and the electrical part is the same. A replacement from another vendor at the same attenuation range will usually match the footprint but not the control polarity or the off chip capacitor requirement, so the substitution should be checked against the reference circuit rather than against the parameter table alone. The RF component sourcing page lists the family, the how to reduce component cost page covers volume pricing across the attenuator range, and footprint differences are on the pin to pin cross reference page.