MAX40200ANS+T
Product Specifications
MAX40200ANS+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX40200ANS+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
MAX40200ANS+T: a 1 A ideal diode that drops 43 mV at 500 mA
The MAX40200ANS+T is an ideal diode current switch in a 4-bump wafer level package measuring 0.73 mm by 0.73 mm by 0.5 mm, with a 0.35 mm bump pitch, tape and reel. In place of a Schottky diode it conducts through a MOSFET, so the forward drop at 500 mA is 43 mV typical and at 1 A it is 85 mV, against the 300 mV to 400 mV a Schottky would take at the same current. It works from 1.5 V to 5.5 V, draws 7 uA of quiescent current, blocks up to 6 V in either direction when disabled, and protects itself thermally.
Published values
| Parameter | Value |
|---|---|
| Supply voltage | 1.5 V to 5.5 V |
| Forward drop | 43 mV typical at 500 mA, 85 mV at 1 A |
| Continuous current | 1 A rating, 1.2 A absolute maximum between VDD and OUT |
| Reverse leakage | 70 nA typical, 1.5 uA maximum when reverse biased |
| Quiescent current | 7 uA typical, 18 uA maximum |
| Disabled state | Blocks up to 6 V in either direction |
| Enable pin current | 10 mA absolute maximum |
| Thermal resistance | 104.41 C/W junction to ambient in the wafer level package |
| Temperature range | Minus 40 C to plus 125 C |
| Package | 4-bump WLP, 0.73 mm by 0.73 mm, top mark +3 |
| Alternate body | 5-pin SOT-23 available as a separate order code |
The 1 A rating and the 1.2 A absolute maximum
The two numbers are close enough to be confused. One amp is the continuous rating, 1.2 A is the absolute maximum between VDD and OUT, which is a survival limit and not an operating point. At 1 A the part drops 85 mV, so it dissipates 85 mW, and the wafer level package is quoted at 104 C/W junction to ambient, which gives a 9 C rise from that dissipation with no copper help. At the absolute maximum of 1.2 A the dissipation is nearer 100 mW and the margin between the rating and the limit is 20 percent. A load that can transiently pull 1.5 A is outside the part, and the thermal protection will fold it back rather than pass it.
Why the tiny drop changes a battery budget
A Schottky diode between a battery and a load wastes 0.3 V to 0.4 V, which on a 3.0 V rail is ten percent of the available headroom and a similar share of the runtime. An ideal diode that drops 43 mV at 500 mA returns that headroom to the load, and because it blocks in both directions when disabled it can also replace the second diode in a two source changeover circuit. The reverse leakage of 70 nA typical, 1.5 uA maximum, is what makes that changeover work without draining the idle source. In a product that sits on a shelf with a charged battery and a USB cable plugged in, this is the part that decides which source is in use and how much of the other one leaks away.
What the enable pin is for
The EN pin turns the pass element off and the part then blocks voltage in either direction up to 6 V, which turns an ideal diode into a load switch with reverse blocking. That is how a single part handles both the OR-ing function and the disconnect, without a second load switch in series. The pin draws at most 10 mA absolute maximum, so it can be driven from a logic output with a series resistor, and it is not a high impedance input. Anyone who treats it as a CMOS gate input and ties it directly to a battery rail will exceed that rating.
Sourcing the wafer level package
The 4-bump wafer level package is the smallest body in this family and it requires a land pattern that most contract houses have never run, so the SOT-23 alternative is worth having on the file even when the flow is expected to work. Package options and the drop in question are covered on the pin to pin cross reference, the cost side of the small body against the SOT-23 is worked through on the component cost page, and the second source position for interface and protection parts is described on ADI part second source.