LTM8067EY#PBF
Product Specifications
LTM8067EY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8067EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8067EY: an isolated 5 V rail for a cabinet that stays above freezing
The LTM8067EY#PBF is the commercial grade of the 2 kVAC isolated flyback module, 3 V to 40 V in, 2.5 V to 24 V out, up to 450 mA at 24 V in and 5 V out, in an 11.25 mm by 9 mm package. The electrical table is the industrial table with one boundary moved: the guarantee starts at 0 degrees rather than -40. For an isolated gate drive or a sensor loop inside a heated cabinet, that is the whole difference, and the part is otherwise identical down to the 2.5 microamp RUN pin current and the 80 mA of input current it draws with the output shorted.
Published values
| Parameter | Value |
|---|---|
| Input range | 3 V to 40 V |
| Output range | 2.5 V to 24 V, set by one resistor |
| Output current | up to 450 mA at 24 V in and 5 V out |
| Isolation | 2 kVAC for one second, 2.83 kVDC equivalent, UL60950 file 464570 |
| Absolute maximum | VIN plus VOUT of 48 V, VOUT relative to VOUTN 25 V |
| Guaranteed range | 0 to +125 degrees internal, TJ maximum 125 degrees |
| Line and load regulation | 1 percent each |
| Output ripple | 30 mV RMS at 100 mA |
| Quiescent current | 3 microamps with RUN at 0 V, 7 mA not switching |
| RUN threshold | 1.214 V falling typical |
| Output short circuit | 80 mA of input current into a shorted output |
| Package | 38 pin BGA, 11.25 mm by 9 mm by 4.92 mm, 1.1 g |
| Thermal | 20.8 degrees per watt to ambient, 5.1 to the board |
| Finish | SAC305 RoHS, tin lead version under the same device code |
The E grade in a heated cabinet
An isolated gate drive sitting next to an IGBT stack is not a cold place. The ambient at the module is often 60 to 70 degrees because the power devices are the heat source, and the 0 degree floor at the bottom of the guarantee is irrelevant, while the 125 degree junction limit at the top is the number that matters. Thirty five degrees of headroom at 20.8 degrees per watt is 1.68 W of dissipation, well above the 0.7 to 0.8 W this module produces at 450 mA out.
The cold end only becomes real if the cabinet is switched off in an unheated building over a weekend and restarted on a Monday morning in January. Start up draws more input current than steady state because the soft start has to charge the output capacitance through the transformer, and that is the moment when behaviour below 0 degrees would matter. If the site can be that cold, the industrial code is the right one.
Sizing the output capacitor is part of the sum rule
A flyback delivers current in pulses, so the output capacitor carries the full load ripple. At 450 mA and 30 mV RMS the ripple current in the capacitor is close to the DC output, which rules out a small ceramic and points at a 22 microfarad or larger electrolytic or polymer part with a ripple current rating above 0.5 A.
The reflected voltage adds to the input during the switch off time, so the input capacitor sees a triangular current that is larger than the DC input. A 2.2 microfarad ceramic at the input pin is the published starting point, and it has to be close enough to the pin that the loop area stays small, otherwise the leakage inductance turns into a voltage spike on the internal switch.
Isolated supplies and the regulatory paper trail
Choosing this module shortens the safety file rather than replacing it. The part is UL60950 recognised, so the component side of the isolation argument is covered, but the end product still needs its own creepage assessment, its own hipot routine in production and its own documentation for the barrier. Buying a recognised component is what makes that assessment short, not what makes it unnecessary.
For a build that ships into the EU, the same applies to the EMC file: the module passes as a tested block with the recommended input and output filters, and any change to those filters is a change to the evidence. Keep the recommended values on the drawing and the test report stays valid.
Two pages worth reading before a purchase order goes out are the power management cross reference and component lead time solutions; the first lists what else fits the socket, the second is the test sequence for a drop in, and the pin to pin cross reference covers the case where the shortage is already on the line.
Two questions buyers ask about this isolated rail
Does the E grade change the isolation rating? No. The 2 kVAC one second test, the UL60950 recognition and the 48 V sum rule are the same on both grades. The isolation barrier is a construction and a test, not a temperature specification.
Can it drive an IGBT gate directly? It can supply the floating rail, not the gate current. The 450 mA is a supply rating; the gate charge has to be delivered by a driver on the isolated side, and the average current that driver draws from the rail is the number to compare with 450 mA.