AD8065ARZ
Product Specifications
AD8065ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8065ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8065ARZ: 145 MHz Is a Gain of One Figure, and a Photodiode Preamp Is Not a Gain of One
The AD8065 is a FET input voltage feedback amplifier with 1 pA of input bias current, a 145 MHz minus 3 dB bandwidth at unity gain, a 180 V per microsecond slew rate and 7 nV per root hertz of input noise, running from 5 V to 24 V supplies at 6.4 mA per amplifier. The two numbers that get quoted together, 145 MHz and 1 pA, belong to different circuits. The bandwidth is a small signal figure at a gain of one; the bias current is what makes a photodiode or a high impedance transducer happy. A transimpedance stage with a 1 Mohm feedback resistor has a noise gain far above one, and its bandwidth is not 145 MHz.
Bandwidth follows the noise gain, not the signal gain
At a closed loop gain of 10 the usable small signal bandwidth falls to roughly a tenth of the unity gain figure, which is 14.5 MHz. The slew rate sets a second ceiling that does not depend on the feedback network: 180 V per microsecond at 2 V peak to peak is about 14 MHz of full power bandwidth, at 4 V peak to peak it is 7.2 MHz, and at 8 V peak to peak it is 3.6 MHz. A stage that needs a 4 V swing at 10 MHz is therefore outside the part whatever the feedback resistor says, and the only fix is a faster amplifier or a smaller swing.
| Parameter | Published value | What it decides |
|---|---|---|
| Unity gain bandwidth | 145 MHz | Small signal ceiling at a gain of one |
| Slew rate | 180 V per microsecond | Full power bandwidth at a given swing |
| Input bias current | 1 pA | Offset into a high impedance source |
| Input voltage noise | 7 nV per root hertz at 10 kHz | Noise floor against source impedance |
| Offset voltage | 1.5 mV maximum | DC error, and the floor for a DC coupled stage |
| Supply current | 6.4 mA per amplifier typical | Budget on a multi channel board |
The bias current only pays above a certain source impedance
One picoamp through 1 Mohm is 1 uV, through 10 Mohm it is 10 uV and through 1 Gohm it is 1 mV. Against a 1.5 mV offset limit, the bias current stops being negligible somewhere around a gigohm, which is exactly the photodiode and electrometer territory this part is sold into. At the other end, 7 nV per root hertz over a 1 MHz band is 7 uV rms, and over a 10 MHz band it is 22 uV, so the noise and not the offset is the limit once the bandwidth is wide. A 12-bit converter on a 5 V range has a 1.2 mV step, which means the amplifier noise in a wideband stage is several steps by itself.
What the output stage can and cannot do
The output is rail to rail, which is what makes the part usable on a single 5 V supply, but rail to rail output does not mean the input stage reaches the rails. Slew rate, settling and distortion numbers are all quoted at a specific load: settling to 0.1 percent on a 2 V step is 55 ns, and the spurious free dynamic range is minus 88 dBc at 1 MHz. Driving a switched capacitor converter input directly puts a capacitive load on the output, and the series resistor that stabilises it also adds a pole that has to be inside the loop.
The shortage question for a FET input part
When this code is short, the substitution has to match input bias current class, supply range and package before bandwidth, because a CMOS input part with 1 pA of bias but a 6 V maximum supply cannot go on a 12 V rail. The amplifier cross reference page covers the family and the grade, the pin to pin cross reference page covers the footprint, and incoming checks follow the incoming inspection plan.