AD8138ARZ-R7
Product Specifications
AD8138ARZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8138ARZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8138ARZ: The 320 MHz Figure Is a 0.5 V Peak to Peak Number
The AD8138 is a differential amplifier built to drive analog to digital converters, with a minus 3 dB bandwidth of 320 MHz at a gain of plus one, 1150 V per microsecond of slew rate, 16 ns settling to 0.01 percent and 5 nV per root hertz of input voltage noise. Every one of those dynamic numbers is specified at 0.5 V or 2 V peak to peak, so the bandwidth a converter front end actually sees depends on the signal amplitude and on the feedback network around the part. The VOCM pin sets the output common mode independently, which is the feature that makes the part useful on a single supply converter with a mid rail reference.
Bandwidth against amplitude
The 320 MHz figure is measured at 0.5 V peak to peak with no feedback capacitor. At 2 V peak to peak the same part is specified at 265 MHz, and 1 pF of feedback capacitance pulls the small signal number down to 225 MHz. A 14 bit converter running a 2 V peak to peak full scale at 100 MSPS therefore has 2.65 times the bandwidth it needs, and an engineer who budgeted from the 320 MHz line has the margin but not the reason. The 0.1 dB flatness point is 40 MHz, which is the number that matters for an intermediate frequency stage rather than the minus 3 dB point.
Settling, slew and the acquisition window
16 ns to 0.01 percent on a 2 V step and 1150 V per microsecond of slew rate are consistent: the slew portion of a 3 V step at that rate is 2.6 ns, and the rest of the 16 ns is the settling tail. In a switched capacitor converter front end the amplifier has to recover from the sampling kick within the acquisition window, and 16 ns leaves room at 10 MSPS and none at 100 MSPS unless the converter has a buffered input. Overdrive recovery is 4 ns, which is the number that matters when the input is driven past full scale by a fault.
| Item | Published value | What it decides |
|---|---|---|
| Bandwidth, gain of one | 320 MHz at 0.5 V peak to peak | 265 MHz at 2 V peak to peak |
| Slew rate | 1150 V per microsecond | 2.6 ns for a 3 V step |
| Settling to 0.01 percent | 16 ns | Acquisition window budget |
| Distortion | minus 94 dBc at 5 MHz, minus 85 dBc at 20 MHz | SFDR at the converter input |
| Supply current | 18 mA typical, 23 mA maximum | 90 mW at 5 V, 115 mW worst case |
Supply and headroom
The part runs on plus and minus 3 V to plus and minus 5 V, and the output common mode is set by the VOCM pin over a range the data sheet publishes as 1.0 V to 3.8 V on a 5 V supply. On a single 5 V rail that window is generous; on a 3 V rail it narrows and the converter reference has to be inside it. Quiescent current is 18 mA typical and 23 mA maximum, which is 115 mW at 5 V and is the reason a four channel front end needs a thermal look before it is placed in a small package.
Gain setting and the input resistance
The feedback resistors are external, and the differential input resistance is 6 kohm typical at a gain of one, so the source sees a load that changes with the gain setting. A 50 ohm source into a 6 kohm input is a 0.8 percent gain error from loading alone, which is 13 counts of a 14 bit converter, and that is before the resistor tolerances. Matching the four resistors to 0.1 percent brings the gain error under a count and is the usual specification for a 14 bit front end.
Where the part stops
Above 20 MHz the second harmonic falls from minus 94 dBc to minus 85 dBc, so an intermediate frequency stage at 70 MHz sees minus 62 dBc, which is 10 effective bits at best. The ADC DAC cross reference page lists the converters and drivers that pair with it, the amplifier cross reference page covers the higher speed alternatives, and lot checks follow the incoming inspection plan.