LTM8052MPV#PBF
Product Specifications
LTM8052MPV#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8052MPV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8052MPV: 5 A source, 6 A sink, constant current and constant voltage
The LTM8052MPV#PBF is a 36 V, 5 A two quadrant step-down module that regulates both voltage and current, and can source or sink output current. The output spans 1.2 V to 24 V from a 6 V to 36 V input, and the current limit is set by a control voltage from 0 to 1.5 V, which is what makes it a TEC driver, a battery charger and an active load in one part number. It sits in an 11.25 mm by 15 mm by 2.82 mm land grid array with a gold pad finish, at 18.6 degrees per watt, guaranteed over -55 to +125 degrees internal.
Published values
| Parameter | Value |
|---|---|
| Input range | 6 V to 36 V |
| Output range | 1.2 V to 24 V, set by RADJ: open for 1.2 V, 499 ohm for 24 V |
| Output current | -6 A sink to +5 A source |
| Current limit control | CTL_I from 0 V to 1.5 V, adjustable at run time |
| Reference | 1.19 V nominal at ADJ, 1.16 V to 1.22 V over temperature |
| Switching frequency | 100 kHz to 1 MHz; RT of 453k gives 100 kHz, 40.2k gives 1 MHz |
| Quiescent current | 0.1 microamp typical, 3 microamp maximum with RUN at 0 V |
| No load current | 17 mA typical, 30 mA maximum |
| Line and load regulation | 0.1 percent and 0.7 percent |
| Output ripple | 10 mV RMS at 12 V in and 4.5 A |
| Overvoltage behaviour | 125 percent output protection on the LTM8052, absent on the LTM8052A |
| Package | LGA, 11.25 mm by 15 mm by 2.82 mm, gold pad finish, MSL 3 |
| Thermal | 18.6 degrees per watt to ambient, 5.4 to the board, 10.8 to the top |
| Temperature grade | -55 to +125 degrees internal |
Sinking current puts energy back into the input
A two quadrant converter that sinks 6 A at 5 V is absorbing 30 W, and in a synchronous topology that energy goes back to the input rail rather than into a heatsink. A lab supply with a bleed resistor absorbs it; a battery being charged absorbs it; a bulk capacitor charges up until something gives. If the input is a diode rectifier or a supply that cannot take reverse current, the input voltage rises until a clamp or a protection trips.
This is the single most common mistake with two quadrant modules. The sink rating is real, but it is a statement about the output stage, not about where the energy goes. Plan the input side for regeneration before specifying the sink current.
The 125 percent overvoltage difference between the two variants
The LTM8052 monitors the output and limits or shuts down when it exceeds 125 percent of the regulated level; the LTM8052A does not, which lets it keep regulating when the load itself pushes the output above the set point. For a battery charger with a battery that can be disconnected, or a TEC driver where the loop opens during a thermal transient, the difference decides whether the rail recovers or the protection latches.
The order code carries the distinction, and the V suffix on this page is the LGA package rather than the BGA. Both packages exist, so a board change from LGA to BGA is a footprint change and not a substitution.
Setting a current limit with a control voltage
CTL_I accepts 0 to 1.5 V and maps it to the current limit, so a DAC or a filtered PWM sets the limit in software. That is what makes the part usable as a programmable charger: the host ramps the limit up, watches the voltage, and the module holds constant current until the battery reaches its set point and then holds constant voltage.
The ADJ pin is the voltage reference at 1.19 V, so a divider sets the float voltage. At 4.2 V per cell for a two cell pack the divider ratio is 3.53:1, and the 1.3 percent reference tolerance is 55 mV on 4.2 V, which is material for a lithium charger and is why a precision divider and a calibration step are worth the effort.
When an order code in this family cannot be found, the power management cross reference lists what else does the same job, medical device components covers what to check before a part is dropped into an existing board, and how to verify a drop in replacement is the route we take on a live shortage.
Two questions buyers ask about the CVCC module
Does the module need an external diode for sinking? No external diode is needed for the two quadrant operation, but the input side has to tolerate the current coming back. That is a system question, not a component one.
Is the MP grade required for a Peltier driver? Not necessarily, but a TEC can drive the module's case below 0 degrees when it is cooling, and a cold ambient plus a cold case is where the MP grade's -55 degree guarantee matters. The I or E grade covers -40 and 0 degrees respectively.