Contact Us

LTM8052EV#PBF

Brand: Analog Devices
Analog Devices LTM8052EV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8052EV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8052EV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8052EV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8052EV: the same 5 A two-quadrant rail with a guarantee that starts at zero

The LTM8052EV#PBF is the commercial grade of the 36 V, 5 A constant-voltage constant-current module, in the same 11.25 mm by 15 mm by 2.82 mm land grid array with the same 1.19 V reference, the same 5.6 A source limit and the same 7.7 A sink limit. What separates it from the industrial code is one line of the specification: the E grade is guaranteed to meet its limits from 0 to +125 degrees internal, and the behaviour down to -40 is assured by characterisation and process control rather than by test. On this particular part the order table lists both the E and the I code over -40 to +125, so the reel label is the only place the grade appears.

Published values

ParameterValue
Input range6 V to 36 V; VIN absolute maximum 40 V
Output range1.2 V to 24 V, set by one resistor from ADJ
Output currentplus or minus 5 A at a 1.5 V control voltage
Source limit5.6 A typical, 5.1 A to 6.1 A over the parts
Sink limit7.7 A typical, 6.9 A to 8.5 A over the parts
Reference output2.00 V at 0.5 mA, used for the control pins
Switching frequency100 kHz to 1 MHz, one resistor
Quiescent current17 mA at no load, 0.1 microamps shut down
Output ripple10 mV RMS at 4.5 A
Load regulation0.7 percent from 0 A to 5 A
Guaranteed range0 to +125 degrees internal; -40 to 0 assured by characterisation
Storage-55 to +125 degrees, so an unheated warehouse is inside the rating
Thermal18.6 degrees per watt to ambient, 5.4 to the board
Package81 lead LGA, 15 mm by 11.25 mm by 2.82 mm, MSL 3

What the zero degree line does and does not change

Every limit in the electrical table still applies over 0 to 125 degrees, including the 5.1 A to 6.1 A spread on the source current limit and the 0.7 percent load regulation. What the E grade does not promise is the value of those limits while the module is below freezing. A product that is stored cold and started cold is asking exactly that question, and the answer has to come from characterisation data rather than from the data sheet.

The practical reading is simple. Indoor equipment, rack units, bench instruments and mains powered industrial boxes never see a cold start, so the E grade is fully specified for the job. Outdoor cabinets, vehicle systems and anything that turns on at minus 20 need the I grade or a written statement from the vendor, and the difference in price is small against the cost of a field failure in a cold climate.

Why a two-quadrant rail is specified on test equipment

Battery testers and supercapacitor cyclers spend half their life pushing current into a cell and half pulling it out, and a one-quadrant regulator cannot do the second half without a separate sink. This module holds its setpoint in both directions, which removes the sink from the bill and removes the handover between charge and discharge that a two-block arrangement always shows as a glitch.

The control pins make the profile easy to drive: an analogue voltage on CTL_I from a digital to analogue converter sets the magnitude, and the direction follows the error between the setpoint and what the cell is doing. The thermistor input on CTL_T is there for the case where the profile has to fold back on temperature, which is the normal requirement for anything with a lithium cell in it.

The three limits that catch a first build

First, the minimum input is 6 V, so a 5 V bus cannot feed a 5 V output. Second, the ADJ pin sources 100 microamps into the divider, which shifts the setpoint if the divider is built from large resistors. Third, the input has to absorb energy when the module sinks, and the 40 V absolute maximum is only 4 V above the operating ceiling, so a clamp belongs on the bus even when the load is well behaved.

None of the three is a module defect. They are the same three points that come up on every two-quadrant supply, and a build that answers them on the first pass does not rediscover them at thermal soak.

Two pages worth reading before a purchase order goes out are component lead time solutions and the power management cross reference; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to verify a drop in replacement covers the case where the shortage is already on the line.

Two questions buyers ask about the E grade

Is the E grade a drop-in for the I grade on an existing board? Electrically yes, same die, same package, same pin out. Contractually the cold start guarantee is gone, so a product specified below 0 degrees needs an engineering sign off and a note in the build record before the swap is made.

Does the E grade carry the same automotive option? No. The -55 degree MP code is the wider screened part in this family, and there is no AEC flow on the module itself. An automotive build has to take the MP grade and the qualification argument that goes with it.