LTM8048IY#PBF
Product Specifications
LTM8048IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8048IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8048IY: a 725 V barrier and a low noise post regulator in one 9 by 11 mm package
The LTM8048IY#PBF is an isolated flyback module with a linear post regulator on the secondary side, in an 11.25 mm by 9 mm by 4.92 mm ball grid array weighing 1.1 g. The controller, the switches and the transformer are inside, so an isolated rail needs output, input and bypass capacitors and nothing else. The flyback output is set from 2.5 V to 13 V by one resistor and delivers up to 440 mA at 2.5 V from a 24 V input. The post regulator then takes that rail down to anything from 1.2 V to 12 V at up to 300 mA, and it is the block that turns a switching rail with 20 mV of ripple into a supply an analogue front end can use.
Published values
| Parameter | Value |
|---|---|
| Input range | 3.1 V to 32 V; BIAS may be tied to VIN or fed separately |
| Isolation | 725 VDC, tested for one second in each polarity |
| Flyback output | 2.5 V to 13 V, set by one resistor from ADJ1 |
| Flyback current | 440 mA at 2.5 V from a 24 V input; the curve falls as the output rises |
| Flyback ripple | 20 mV RMS at 0.1 A |
| Line and load regulation | 1.7 percent and 1.5 percent on the flyback output |
| Post regulator output | 1.2 V to 12 V at up to 300 mA, ADJ2 reference 1.22 V |
| Post regulator dropout | 0.25 V at 10 mA, 0.34 V at 100 mA, 0.43 V at 300 mA |
| Post regulator ripple | 20 microvolts RMS with a 0.01 microfarad bypass capacitor, 100 Hz to 100 kHz |
| Quiescent current | 850 microamps not switching, 1 microamp shut down |
| BIAS current | 8 mA at 12 V in with a 5 V BIAS and 100 mA of load; 3.1 V is the minimum BIAS |
| Short circuit current | 30 mA into a shorted flyback output |
| Thermal | 23.2 degrees per watt junction to ambient, 5.8 to the board, 6.7 to the board junction |
| Package | 45 lead BGA, 11.25 mm by 9 mm by 4.92 mm, MSL 3, 1.1 g |
| Temperature | this code is guaranteed over -40 to +125 degrees internal |
The isolation figure is a withstand test, not a working voltage
The data sheet states that the barrier is tested at 725 VDC for one second in each polarity. That is a production hipot at a defined stress, and it answers the question a safety reviewer asks about a barrier surviving a fault. It is not a statement that 725 V may be applied continuously between the two grounds, and it is not a reinforced rating for mains working voltage.
For a sensor loop, a current shunt on a high side or a ground loop between two cabinets, the number that matters is a few hundred volts of continuous difference plus whatever transient the installation can deliver. A build that treats the hipot figure as a continuous rating is the one that comes back from a surge test, so the barrier question belongs with the system isolation requirement rather than with this table.
Why a switching rail and a linear regulator share one package
An isolated rail is what breaks the ground loop, but a flyback secondary carries switching ripple at 20 mV RMS and a switching edge that couples into everything it feeds. Putting a linear post regulator after it costs headroom and buys quiet: the LDO rejects the switching content down to 20 microvolts RMS once a 0.01 microfarad bypass capacitor is fitted, which is three orders of magnitude below the input ripple.
The cost is the dropout. At 300 mA the regulator needs 0.43 V of headroom, so the flyback rail has to sit at least 0.43 V above the post regulator output, and more if the flyback output has 1.5 percent load regulation over the load step. A 3.3 V analogue rail therefore wants the flyback set near 4 V, not at 3.3 V.
The thermal budget is shared, and the post regulator spends most of it
Both blocks sit in one 11.25 mm by 9 mm body with 23.2 degrees per watt to ambient, so at an 85 degree ambient the pair has 40 degrees of headroom and 1.72 W of dissipation between them. A flyback at 2.5 V and 440 mA is 1.1 W out; at three quarters efficiency that is 0.37 W of loss. That leaves 1.35 W for the linear regulator, which at 300 mA allows 4.5 V of drop.
Run the same regulator from a 12 V flyback rail down to 3.3 V and the drop is 8.7 V, which at 300 mA is 2.6 W, well past the whole package budget before the flyback takes anything. The 300 mA rating is real, but it belongs to a small drop, and the deliverable current at a large drop has to be computed from the thermal allowance rather than read off the feature list.
Buyers usually arrive at the power management cross reference to find the family alternatives, then use OEM procurement to confirm a substitute before it is fitted; how to verify a drop in replacement is the routine for a part that has already stopped shipping.
Two questions buyers ask about the isolated regulator
Can the post regulator run from an external rail with the flyback off? Yes. The electrical table specifies the post regulator with RUN at 0 V and a voltage applied to the flyback output, so the LDO is characterised on its own. That allows a board to use the regulator as a standalone low noise stage when the isolated side is not needed.
Does the module need a separate BIAS supply? It runs with BIAS tied to VIN, but a separate BIAS at 5 V cuts the internal dissipation and improves efficiency. The minimum is 3.1 V, and the pin draws 8 mA at 12 V in with 100 mA of load.