Contact Us

LTM8033IY#PBF

Brand: Analog Devices
Analog Devices LTM8033IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8033IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8033IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8033IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8033IY: a 3 A, 36 V buck module built for the emissions test, not just for the current

The LTM8033IY#PBF is a 36 V input, 3 A step-down module built against the radiated emissions requirement of EN55022, in an 11.25 mm by 15 mm by 4.92 mm ball grid array weighing 2.2 g. The controller, the switches, the inductor and an input filter are inside, so what is left on the board is bulk input and output capacitance. Output spans 0.8 V to 24 V, switching spans 200 kHz to 2.4 MHz with one resistor each, and up to four modules can share current for more than 3 A. The industrial code is guaranteed over -40 to +125 degrees internal.

Published values

ParameterValue
Input range3.6 V to 36 V
Output range0.8 V with ADJ open to 24 V with a 16.5k resistor at 32 V in
Output current3 A at 24 V in; more with the SHARE pin across modules
Switching frequency780 kHz with RT at 45.3k; 200 kHz to 2.4 MHz in total
Feedback reference790 mV nominal, 775 mV to 805 mV over the parts
Quiescent current30 microamps not switching, 0.01 microamp shut down
Line and load regulation0.3 percent and 0.4 percent
Output ripple5 mV RMS
Emissionsradiated to EN55022 Class B; conducted needs the standard filter parts
Power good730 mV rising threshold at the ADJ pin, 200 microamps of sink
Minimum BIAS2.8 V for proper operation; 2 V typical
Thermal15.4 degrees per watt to ambient, 5.2 to the board, 16.7 to the top
Package76 lead BGA, 11.25 mm by 15 mm by 4.92 mm, MSL 3, 2.2 g
Temperatureguaranteed -40 to +125 degrees internal

The emissions claim is about radiation, and the conducted part is yours

The module is specified against the radiated requirement of EN55022 Class B, which is the part that no board change can fix once the switching loop is set. Conducted emissions are met by adding standard filter components, and the data sheet gives the measured levels at 500 kHz into a line impedance network so the filter can be sized rather than guessed.

The practical consequence for a review is that this part removes the hardest half of the problem and leaves a predictable half. A board that fails conducted emissions with this module has a filter that is too small or placed too far from the connector, not a fundamental problem with the converter.

Three amps at 24 volts out is an efficiency question

At an 85 degree ambient the 15.4 degrees per watt path allows 2.6 W of dissipation. Three amps at 3.3 V is 9.9 W out, which needs 79 percent efficiency, and three amps at 12 V is 36 W out, which needs 93 percent. Three amps at 24 V would be 72 W out and would need 96.5 percent, past what any converter of this size does.

So the honest statement of the rating is that 3 A is available at the low and middle of the output range and has to be derated toward 24 V. The 24 V figure in the electrical table is a voltage ceiling reached with a 16.5 k resistor from a 32 V input, and it is not a promise of 3 A at that point.

Sharing current, and what has to match

The SHARE pin lets several modules divide the load, which is how the family reaches currents above 3 A without a second part number. Sharing only works if the modules see the same input, run the same frequency and are trimmed to the same output, so the frequency resistor and the feedback divider have to be identical, and the modules have to be placed so their input and output impedances match.

An unmatched pair will share unevenly and one module will run hot while the other idles, which looks like a thermal problem and is really a tolerance problem. The pin is not a current sharing bus in the usual sense: it is a share adjust, and the loop expects the paralleled outputs to be joined at the load, not at the module pins.

When an order code in this family cannot be found, the power management cross reference lists what else does the same job, OEM procurement covers what to check before a part is dropped into an existing board, and defense grade components is the route we take on a live shortage.

Two questions buyers ask about the EMC module

Does this module pass EN55022 on its own? The radiated requirement, yes, as specified. Conducted emissions need the standard filter components in front of the input, and the measured levels in the data sheet tell you how much attenuation the filter has to supply.

Can I get 6 A by paralleling two modules? Yes, with the SHARE pin and matched frequency and feedback. Both modules need the same input and output nets and a symmetric placement, otherwise the sharing is uneven and one runs hot.