Contact Us

LTM8033IV#PBF

Brand: Analog Devices
Analog Devices LTM8033IV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8033IV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8033IV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8033IV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8033IV: the 3 A EMC module in the land grid array, and what the last letter changes

The LTM8033IV#PBF is the industrial grade of the 36 V, 3 A step-down module in the land grid array body: 11.25 mm by 15 mm by 4.32 mm, 76 pads, 2.2 g. The letter after the grade is the package, not the temperature. A V suffix is the gold pad LGA with the e4 finish, and a Y suffix is the ball grid array at 4.92 mm with SAC305 balls and the e1 finish. Electrically the two are the same converter, with 0.8 V to 24 V out, 200 kHz to 2.4 MHz switching, a 790 mV reference and 5 mV RMS of output ripple, so the choice between them is a board process decision rather than an electrical one.

Published values

ParameterValue
Input range3.6 V to 36 V
Output range0.8 V to 24 V
Output current3 A at 24 V in
Switching frequency780 kHz with RT at 45.3k, 200 kHz to 2.4 MHz in total
Reference790 mV at the ADJ pin, 775 mV to 805 mV over the parts
Quiescent current30 microamps not switching, 0.01 microamp shut down
Output ripple5 mV RMS
Line and load regulation0.3 percent and 0.4 percent
Emissionsradiated to EN55022 Class B
Thermal15.4 degrees per watt to ambient, 5.2 to the board, 16.7 to the top
Package76 pad LGA, 11.25 mm by 15 mm by 4.32 mm, MSL 3, 2.2 g
Finishgold pad, e4, RoHS
Temperatureguaranteed -40 to +125 degrees internal

Land grid array against ball grid array, on the line rather than on paper

An LGA has pads on the package and no balls, so the solder volume comes entirely from the stencil. That gives a lower standoff, 4.32 mm against 4.92 mm, and it removes the collapse step that a BGA goes through, which makes the joint height a printing decision rather than a reflow one. On a board with height pressure under a connector or a lid, the 0.6 mm difference is sometimes the reason the part is chosen.

The trade is that an LGA forgives nothing. Coplanarity, paste volume and pad finish all have to be right, and a reflow profile that sags a BGA into place will not pull an LGA down. A BGA self aligns on its own surface tension during reflow, which is why high volume lines with a wide process window often prefer the Y code even when the height allows the V code.

The thermal path is the same in both bodies

Both packages publish 15.4 degrees per watt junction to ambient, 5.2 to the board and 16.7 to the top, on a board defined by the JEDEC test. The numbers are identical because the heat leaves through the pads and the copper under them, not through the lid. That means the copper and the vias are part of the thermal answer for either code, and a board that runs cool with one will run cool with the other as long as the pad pattern and the plane are equivalent.

At an 85 degree ambient the budget is 2.6 W. Three amps at 3.3 V is 9.9 W out and needs 79 percent efficiency, three amps at 12 V is 36 W out and needs 93 percent. The 24 V output is a voltage ceiling reached with a 16.5 k resistor from a 32 V input, not a promise of 3 A at that point.

What the gold pad finish is for

The e4 finish is a gold pad over nickel, which keeps the pad flat and solderable through storage and gives a defined intermetallic at the joint. It also survives rework better than a bare copper pad, which matters on a module that costs real money and is often the last part placed. The BGA version carries SAC305 balls with the e1 finish, and both are RoHS and MSL 3 with 168 hours of floor life.

Neither finish changes the electrical table. A customer comparing quotes on the V and Y codes is comparing assembly yield, rework cost and height, not performance, and the order line should say which one the stencil and the reflow profile were qualified for.

Sourcing notes for this family: the power management cross reference holds the cross references, OEM procurement is the pre substitution check, and how to verify a drop in replacement is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask about the package code

Is the V code a different temperature grade from the Y code? No. The letter is the package. LTM8033IV and LTM8033IY are both industrial at -40 to +125, one in the land grid array and one in the ball grid array; the EV and EY codes are the same pair in the commercial grade.

Can I mix the two packages on one board? Not in one footprint. The pad pattern, the standoff and the reflow profile differ, so a board qualified for one code needs a new stencil and a new profile for the other even though the electrical behaviour is the same.