Contact Us

LTM8032IV#PBF

Brand: Analog Devices
Analog Devices LTM8032IV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8032IV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8032IV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8032IV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8032IV: 2 A of quiet 36 V conversion in a 2.82 mm package

The LTM8032IV#PBF is a 36 V input, 2 A step-down module built against the radiated emissions requirement of EN55022, in a 9 mm by 15 mm by 2.82 mm land grid array that weighs 1.2 g. The controller, the switches, the inductor and an input filter are inside, and the height means the part can go on the underside of a board under a connector or a display. Output spans 0.8 V to 10 V, switching spans 200 kHz to 2.4 MHz with one resistor, and the reference is 790 mV with 6 mV RMS of output ripple. The industrial code is guaranteed over -40 to +125 degrees internal.

Published values

ParameterValue
Input range3.6 V to 36 V; 40 V absolute maximum on VIN, FIN and RUN/SS
Output range0.8 V with ADJ open to 10 V with a 21.6k resistor
Output current2 A at 24 V in
Switching frequency325 kHz with RT at 113k, 200 kHz to 2.4 MHz in total
Reference790 mV at ADJ, 765 mV to 815 mV over the parts
Quiescent current25 microamps not switching, 0.6 microamp maximum shut down
Output ripple6 mV RMS at 2 A and 3.3 V
Line and load regulation0.1 percent and 0.3 percent
Auxiliary outputAUX is current limited to 100 mA
Thermal25.2 degrees per watt to ambient, 10.3 to the board, 15.8 to the top
Package71 pad LGA, 9 mm by 15 mm by 2.82 mm, MSL 3, 1.2 g
Temperatureguaranteed -40 to +125 degrees internal

Two amps in a package thin enough for the back of the board

A 2.82 mm body fits where a caged inductor and a controller do not, and the underside of a board is usually free space. The trade is thermal: 25.2 degrees per watt junction to ambient means the module depends on the copper under it, and at an 85 degree ambient the budget is 1.59 W of dissipation. Two amps at 3.3 V is 6.6 W out and needs 81 percent efficiency, two amps at 5 V is 10 W out and needs 86 percent.

Mounting it on the underside means the heat has to cross the board to reach air, so the plane and the vias matter more than they would on the top side. A board with a continuous ground plane under the part meets the number; one with a plane split by signal traces does not, and the failure is a hot spot that appears only at full load and only in a sealed box.

The auxiliary output and the parts that hang off it

The AUX pin provides a rail for the internal circuit and can supply a small external load, limited to 100 mA. It is not a second regulated output and it is not a substitute for the BIAS pin, which needs 1.9 V minimum and 2.8 V for proper operation. A build that hangs an LED or a small sensor from AUX is inside the limit; one that powers a second converter from it is not.

The RUN/SS pin sets both the enable threshold and the soft start ramp, with 5 to 10 microamps of pin current, so a capacitor on that pin decides how fast the output rises. On a board with a large output capacitance and an input supply with a current limit, that capacitor is what keeps the input from being pulled down at every power up.

Reading the emissions claim correctly

The module is specified against the radiated part of EN55022 Class B. Conducted emissions are met by adding standard filter components, and the data sheet carries the measured spectrum so the filter can be sized from data rather than from a rule of thumb. The input filter inside the module is what makes the radiated figure possible, and it is also why the input capacitor has to be close: a long trace between the connector and the module bypasses the filter and reopens the problem.

For a product that has to pass a full EMC suite, the practical sequence is to run the module as specified, measure with the intended filter, and only then tune. Changing the switching frequency to dodge a failing band is the last resort, because it usually moves the problem rather than removing it.

Where a customer needs a second position on this part, the power management cross reference is the starting point, OEM procurement sets out the checks a substitution has to pass, and defense grade components is the short lead time route we quote against.

Two questions buyers ask about the 2 A module

Is the LTM8031 a drop-in for this part? Pin compatible, yes, and it is rated 1 A against 2 A here. The reverse substitution, a 1 A part in a 2 A socket, is the one that fails at load. The LTM8031 page and this one share the pad pattern.

What is the input voltage needed to start? The typical circuit is marked 7 V to 36 V for start-up with the running minimum at 3.6 V in the electrical table, so a 5 V rail can run the module but cannot start it. Check the start-up section before specifying a low voltage input.