LTM8031IV#PBF
Product Specifications
LTM8031IV#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8031IV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8031IV: 1 A in the same pad pattern as the 2 A module
The LTM8031IV#PBF is the 36 V, 1 A member of the quiet step-down family, in a 9 mm by 15 mm by 2.82 mm land grid array that is pin compatible with the 2 A LTM8032. That compatibility is the reason the part exists in many builds: a board can be laid out once and populated at 1 A or 2 A depending on the load, with the same pad pattern, the same frequency resistor and the same feedback divider. Output spans 0.8 V to 10 V, switching spans 200 kHz to 2.4 MHz, the reference is 790 mV and the ripple is 6 mV RMS at 1 A. The industrial code is guaranteed over -40 to +125 degrees internal.
Published values
| Parameter | Value |
|---|---|
| Input range | 3.6 V to 36 V |
| Output range | 0.8 V to 10 V |
| Output current | 1 A at 24 V in |
| Switching frequency | 325 kHz with RT at 113k, 200 kHz to 2.4 MHz in total |
| Reference | 790 mV at ADJ, 765 mV to 815 mV over the parts |
| Quiescent current | 25 microamps not switching, 0.6 microamp shut down |
| Output ripple | 6 mV RMS at 1 A and 3.3 V |
| Line and load regulation | 0.1 percent and 0.3 percent |
| Emissions | radiated to EN55022 Class B with margin |
| Thermal | 20.7 degrees per watt to ambient, 8.4 to the board |
| Package | 71 pad LGA, 9 mm by 15 mm by 2.82 mm, MSL 3, 1.2 g |
| Compatibility | pin compatible with the LTM8032 and the LTM8031E code |
One footprint, two current ratings
A product family usually has a base unit and a larger unit that differ in load rather than in architecture. Basing the supply on a footprint that accepts both the 1 A and the 2 A part removes a second board, a second set of approvals and a second set of spares. The frequency resistor and the feedback divider do not change between them, so the bill difference is the module and nothing else.
The trap is thermal rather than electrical. The 1 A part publishes 20.7 degrees per watt and the 2 A part 25.2, which means the smaller part is not simply a derated version of the larger one: it has a better thermal path and a lower dissipation, so a board built for 2 A and populated at 1 A runs cooler than the numbers suggest, and the reverse substitution runs hotter.
The current that a 2.82 mm body can carry
At an 85 degree ambient the 20.7 degrees per watt path allows 1.93 W. One amp at 3.3 V is 3.3 W out and needs 63 percent efficiency, one amp at 5 V is 5 W out and needs 72 percent, and one amp at 10 V is 10 W out and needs 84 percent. All three are inside what the converter does, which is why the 1 A rating holds across the range rather than only at the bottom.
The 2 A part cannot make the same claim at the top of its range, and that is the honest difference between the two codes. A customer who needs 1 A at 10 V is not giving anything up by taking the smaller module, and a customer who needs 2 A at 10 V should be looking at the thermal curve before the order goes out.
Emissions, and the filter that is already inside
The module is specified against the radiated requirement of EN55022 Class B with margin, and an input filter is part of the package. The filter only works if the input capacitor is close to the module and the input trace is short, because the trace is what couples the switching current around the filter and back into the harness.
Conducted emissions still need the standard external filter parts. The data sheet carries the measured spectrum for the module alone, so the attenuation the external filter has to provide can be read off rather than guessed, which is usually the difference between one EMC iteration and three.
For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, how to verify a drop in replacement is the check list before a substitute goes in, and OEM procurement is how a gap is covered without a new line item.
Two questions buyers ask about the 1 A module
Is the LTM8032 a direct substitute for this part? Yes, pin compatible and rated 2 A instead of 1 A. Going up in current on the same footprint is safe from a footprint point of view and has to be checked thermally, because the 2 A part publishes a higher junction to ambient resistance.
Does it come in a ball grid array package? No. This code is the 71 pad land grid array only, 2.82 mm high. The ball grid array body in this family belongs to the LTM8032 codes.