Contact Us

LTM8031EV#PBF

Brand: Analog Devices
Analog Devices LTM8031EV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8031EV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8031EV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8031EV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8031EV: the 1 A quiet module with a guarantee from zero degrees

The LTM8031EV#PBF is the commercial grade of the 36 V, 1 A step-down module in the 9 mm by 15 mm by 2.82 mm land grid array, pin compatible with the 2 A LTM8032. Output is 0.8 V to 10 V, switching is 200 kHz to 2.4 MHz, the reference is 790 mV and the ripple is 6 mV RMS at 1 A. Its limits are guaranteed from 0 to +125 degrees internal, with the range below freezing assured by characterisation, so it fits a bench instrument, a rack card or a wall adapter product that is only started indoors.

Published values

ParameterValue
Input range3.6 V to 36 V
Output range0.8 V to 10 V
Output current1 A
Switching frequency200 kHz to 2.4 MHz; 325 kHz with RT at 113k
Reference790 mV at ADJ, 765 mV to 815 mV
Guaranteed range0 to +125 degrees internal
Quiescent current25 microamps not switching, 0.6 microamp shut down
Output ripple6 mV RMS at 1 A
Thermal20.7 degrees per watt to ambient, 8.4 to the board
Package71 pad LGA, 9 mm by 15 mm by 2.82 mm, MSL 3, 1.2 g
Emissionsradiated to EN55022 Class B with margin
Compatibilitysame pad pattern as the LTM8032

What a wall adapter product actually needs

A product fed from a 12 V or 24 V adapter sees a wide input because the adapter is unregulated at light load and sags at full load. A 36 V rated module covers that with margin, and the 3.6 V minimum running voltage means the rail keeps regulating while a motor or a relay pulls the adapter down. The E grade covers the temperature inside such a product with room to spare.

The cold start question does not arise, which is why the commercial code is the right one here rather than a compromise. The part is identical to the industrial code above freezing, including the 20.7 degrees per watt thermal path, so nothing about the electrical behaviour changes.

One amp in a thin package, without a hotspot

At an 85 degree ambient the budget is 1.93 W of dissipation. One amp at 5 V is 5 W out and needs 72 percent efficiency, one amp at 3.3 V needs 63 percent, and one amp at 10 V needs 84 percent. The last number is the one to check on a sealed product, because 10 V out at 1 A is 10 W in a body that relies on the board for cooling.

The 2.82 mm height lets the module go on the underside of the board, and that is usually where the copper is free. The plane under the part and the vias through it are the heat path, and a board with a continuous plane under the module meets the published number while a two layer board with a split plane does not.

Set points, soft start and the pins around them

The output is set by one resistor on ADJ against 790 mV, with 4 microamps flowing out of the pin, so a divider built from large resistors shifts the setpoint. The RUN/SS pin carries 5 to 10 microamps and sets both the enable threshold and the ramp, so one capacitor decides how the output comes up. The PGOOD output is referenced to the ADJ pin at 730 mV rising, which makes it a function of the setpoint rather than of an absolute voltage.

The BIAS pin needs 1.9 V minimum and 2.8 V for proper operation. Tying it to the output cuts the internal dissipation, which is worth doing on a 24 V input where the housekeeping current is a larger share of the loss than at 12 V.

Sourcing notes for this family: OEM procurement holds the cross references, the power management cross reference is the pre substitution check, and vendor consolidation is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask about the 1 A E grade

Is this the same footprint as the 2 A part? Yes, 71 pads on a 9 mm by 15 mm body. The frequency resistor and the feedback divider carry over unchanged, so a board can be populated at either rating.

Does the module include the inductor? Yes, the inductor and an input filter are inside the package. The external parts are bulk input and output capacitors, the frequency resistor, the feedback divider and the soft start capacitor.