ADG3308BRUZ-REEL
Product Specifications
ADG3308BRUZ-REEL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG3308BRUZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG3308: Eight Bidirectional Channels Without a Direction Pin
The ADG3308 is an eight channel bidirectional logic level translator that runs from 1.15 V to 5.5 V, draws under 1 microamp of quiescent current, and needs no direction pin. One side is powered from VCCA and the other from VCCY, and VCCA must always be lower than VCCY for correct operation, which is the single constraint that catches most first boards. Logic levels on the A side are set by VCCA and appear as VCCY compatible levels on the Y side, and the same happens in the other direction without any signal to say which way the data is going. Maximum data rate is 50 Mbps, propagation delay is 6 to 10 nanoseconds, and the part comes in a 20-lead TSSOP or a 20-lead LFCSP.
How a translator works without a direction pin
The channels are built around a one shot that accelerates the edge when it detects a transition, and the side that is driving wins. That means a bus with two devices driving at once will be resolved by whichever is stronger, not by the logic, so the part belongs on a point to point link or on a bus with a single talker at a time. It also means the translator does not care whether the data is a clock, an I2C line or a UART, which is why it appears on so many boards where the processor runs at 1.8 V and the peripheral runs at 3.3 V. The one shot adds a small pulse of current at each edge, so the quiescent current figure is not the whole supply current story on a fast bus.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Channels | 8 bidirectional | ADG3304 is the 4 channel member |
| Supply range | 1.15 V to 5.5 V on both sides | VCCA must be below VCCY |
| Quiescent current | Under 1 microamp | Edge acceleration adds current during switching |
| Data rate | 50 Mbps maximum | Propagation 6 to 10 nanoseconds |
| Direction control | None required | Automatic, one shot assisted edges |
| Enable pin | EN referred to VCCY on the ADG3308 | On the ADG3308-1 it is referred to VCCA |
| Packages | 20-lead TSSOP, 20-lead LFCSP | ADG3308-1 is a 20-ball WLCSP |
| Temperature | Minus 40 C to plus 85 C | Guaranteed over the whole supply range |
The A below Y rule and what happens when it is broken
VCCA must be less than VCCY. On a board where the low voltage side is 1.8 V and the high side is 3.3 V this is natural, and the constraint disappears from view. On a board where the rail order at power up puts VCCY below VCCA for a few milliseconds, the part sees a condition outside its specification and the outputs can do anything, which usually shows up as a peripheral that fails to enumerate after a warm restart but works from cold. The fix is a sequencing rule or a load switch, not a different translator, and it is worth reading the power supply sequencing section before the board is released rather than after the first field return.
Where level translation is the whole problem
Smart card readers, portable communication devices, network switches, storage systems and GPS receivers all contain a processor that runs at one voltage and a peripheral that runs at another, and in each case the translator is the component that decides whether the two can talk. A discrete translator built from resistors and a MOSFET works at low speed and costs board area per channel, and an eight channel part replaces it with one footprint. What the translator does not do is isolate: a fault on the high voltage side passes through to the low voltage side, and a system that needs isolation wants a digital isolator rather than a level translator. Separating those two requirements early saves a respin.
Procurement and second source
Pin compatible translators from other vendors exist, and the differences that matter are the direction behaviour, the data rate and the enable pin reference. The MCU cross reference covers the processors this part typically sits next to, pin to pin cross reference lists the drops that need no board change, and how to verify a drop in replacement sets out the bench checks, including the one that catches an enable pin referred to the wrong rail.