LTM8027MPV#PBF
Product Specifications
LTM8027MPV#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8027MPV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8027MPV: a 60 V, 4 A module screened to start at minus fifty five
The LTM8027MPV#PBF is the wide temperature code of the 60 V, 4 A step-down module: 4.5 V to 60 V in, up to 24 V out, 100 kHz to 500 kHz switching, in a 15 mm by 15 mm by 4.32 mm land grid array with 113 pads and a mass of 2.6 g. The MP grade is guaranteed from -55 to +125 degrees internal, which is the temperature at which telecom, avionics and heavy equipment installations are specified to start. The controller, the switches, the inductor and the support parts are inside, so the external bill is bulk input and output capacitors, one frequency resistor and the divider.
Published values
| Parameter | Value |
|---|---|
| Input range | 4.5 V to 60 V running; 7.5 V minimum to start |
| Undervoltage lockout | 4.6 V rising, 3.7 V falling |
| Output range | 2.5 V to 24 V, set by a divider against a 1.224 V reference |
| Output current | 4 A at 12 V out from an input up to 60 V |
| Switching frequency | 100 kHz with RT at 187k, 500 kHz with RT at 23.7k |
| Feedback | 1.224 V nominal at ADJ, 1.215 V to 1.245 V; the internal feedback resistor is 499k |
| Quiescent current | 39 mA at no load, 9 microamps shut down |
| Line and load regulation | 0.2 percent and 0.2 percent |
| Bias rails | BIAS1 lockout at 6.5 V rising, BIAS2 minimum 3 V, 8.5 V to overdrive the internal regulator |
| Thermal | 12.2 degrees per watt to ambient, 9.3 to the top |
| Package | 113 pad LGA, 15 mm by 15 mm by 4.32 mm, MSL 3, 2.6 g |
| Temperature | guaranteed -55 to +125 degrees internal |
| Efficiency | up to 95 percent in the 48 V to 12 V application |
The start voltage and the lockout are two different numbers
The module runs from 4.5 V and starts at 7.5 V, while the undervoltage lockout releases at 4.6 V rising and drops out at 3.7 V falling. That combination is deliberate: a 48 V bus that sags during a brownout stays in regulation down to the lockout, but a 5 V rail cannot bring the part up at all. Quoting 4.5 V as the minimum input without the 7.5 V start figure is the mistake that produces a board which works on the bench supply and not on the real rail.
At the cold extreme the margin matters more, because the start threshold moves with temperature and the input capacitors lose capacitance. A telecom board specified to start at -55 has to meet the 7.5 V figure with the capacitors it actually has at that temperature, not with the room temperature value.
Four amps at 12 V is 48 W, and the thermal path is the deciding number
Twelve and a quarter degrees per watt means 3.28 W of dissipation at an 85 degree ambient before the junction reaches 125. Four amps at 12 V is 48 W out, so the module needs 93.6 percent efficiency to hold the rating, and the data sheet claims up to 95 percent in exactly that application, from a 16 V to 60 V input. At 24 V out the same current would be 96 W and would need 96.7 percent, which is outside the part, so the top of the output range is a derated point.
The other thermal lever is input voltage. The switch has to block the full input, and switching loss rises with it, which is why the efficiency curve is best at 16 V to 24 V in and falls at 60 V. A 48 V telecom rail sits in the middle of that curve, which is where the family was aimed.
Two bias pins, and why the second one exists
BIAS1 powers the internal housekeeping from the output or from an auxiliary rail and has its own lockout at 6.5 V rising and 6 V falling, drawing 25 mA at no load. Before that rail is up, the part runs from the input through an internal regulator. The 8.5 V figure is the voltage needed to fully overdrive that regulator and take the dissipation off the input side.
On a 60 V input that matters: the internal regulator has to drop 60 V to a few volts, and the current it passes becomes heat inside the package. Feeding BIAS1 from a 12 V auxiliary rail removes most of it. BIAS2 needs 3 V minimum and draws 1 microamp, and it is the pin that takes a small external rail when the main bias is not available at start-up.
When an order code in this family cannot be found, defense grade components lists what else does the same job, component obsolescence management covers what to check before a part is dropped into an existing board, and the power management cross reference is the route we take on a live shortage.
Two questions buyers ask about the 60 V MP code
Is the MP grade available in the ball grid array as well? Yes, LTM8027MPY#PBF in the 15 mm by 15 mm by 4.92 mm body with SAC305 balls, and LTM8027MPY in tin lead. The LGA code here is the 4.32 mm body with gold pads.
Can it run from a 5 V bus? It runs down to 4.5 V but needs 7.5 V to start, so a 5 V rail cannot bring it up on its own. A 12 V or 24 V rail is the normal input, and the 60 V rating is there for transients and for 48 V systems.