LTM8023MPY#PBF
Product Specifications
LTM8023MPY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8023MPY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8023MPY#PBF: The Minus 55 Degree Version of the 36 V, 2 A Step-Down Module
The LTM8023MPY#PBF is the widest temperature grade of a 2 A step-down module that contains the switching controller, both power switches, the inductor and the support components in one over-moulded package. The input range is 3.6 V to 36 V, the output range is 0.8 V to 10 V set by one resistor, the switching frequency is selectable from 200 kHz to 2.4 MHz, and the body is the ball grid array version measuring 9 mm by 11.25 mm by 3.42 mm. The MP suffix is the reason to buy this order code: minus 55 to plus 125 degrees ambient, where the E and I grades stop at plus 85. Everything else on the page is the same module as the other four codes in the family.
What the MP grade actually guarantees
The ordering table separates three things that are easy to confuse: the ambient range over which the part is guaranteed to meet its specifications, the range over which it will operate, and the range over which it is characterised. The MP grade is guaranteed over minus 55 to plus 125 degrees, the I grade over minus 40 to plus 85, and the E grade is guaranteed from 0 to plus 85 with the colder part of its minus 40 range assured by characterisation rather than by test. A cold soak to minus 40 degrees in a vehicle or an outdoor enclosure is therefore an I or MP decision and not an E decision, and the price difference between the codes exists for that reason alone.
The adjust pin regulates to 0.79 V, not to 0.8 V
The feedback threshold is 0.79 V and the adjust resistor follows the equation RADJ equals 394.21 divided by the output voltage minus 0.79, with the resistor in kilo ohms. A 3.3 V output needs about 157 kohm, a 2.5 V output about 230 kohm and a 1.2 V output about 962 kohm. The 0.79 V threshold is also the floor of the output range: an output at 0.8 V needs a resistor of nearly 4 Mohm and an output below 0.79 V is not reachable at all, so a 0.75 V core rail is outside the part even though the front page says the range starts at 0.8 V. Adding a second resistor to lift the feedback node is possible but it changes the loop gain and has to be checked against the module's internal compensation.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Input range | 3.6 V to 36 V | 12 V, 24 V and 28 V rails directly |
| Output current | 2 A | The module is rated at the output, not the switch |
| Output range | 0.8 V to 10 V, one resistor | 0.79 V threshold is the real floor |
| Switching frequency | 200 kHz to 2.4 MHz, one resistor | Frequency is a board area and loss trade |
| Temperature grade | MP, minus 55 to plus 125 degrees | The E and I grades stop at plus 85 |
| Package | BGA, 9 mm by 11.25 mm by 3.42 mm | Balls are the only thermal path to the board |
| Ball finish | SAC305, RoHS | The non PBF codes use tin lead |
| Moisture sensitivity | MSL 3 | Floor life applies once the dry pack is opened |
| Start-up input | 5.5 V with RUN/SS tied to the input | 3.5 V is enough to run, not to start |
Start-up is the specification people miss
The module needs about 3.5 V of input to run a 3.3 V output at light load but about 5.5 V to start when the RUN/SS pin is tied to the input, and about 4.5 V to start when the pin is used to enable the module after the input has settled. That difference is the reason a 5 V rail at the bottom of its tolerance can fail to bring up a 3.3 V module that works perfectly on the bench at 5.2 V. The RUN/SS pin also sets the soft-start ramp through a capacitor, so the inrush into the output capacitance is a component choice, and a system with a large bulk capacitor has to size that ramp or the input supply will current limit at every power-up.
Where the MP grade is needed
Outdoor telecom equipment, industrial cabinets that are not heated, automotive body electronics away from the engine bay and any enclosure that has to survive a cold start below minus 40 degrees are the sockets that justify the MP code. Where the operating range is 0 to 70 degrees inside a rack, the E grade is the same module for less money, and where the range is minus 40 to plus 85 the I grade is enough. The pin to pin cross reference covers the LGA and BGA body choice within the family, the ADI part second source page sets out what a substitute module has to match, and the one stop BOM sourcing page covers the module with its capacitors on one order.