Contact Us

LTM8023EY#PBF

Brand: Analog Devices
Analog Devices LTM8023EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8023EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8023EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8023EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8023EY#PBF: The E Grade 2 A Module, and What Its Zero Degree Limit Really Means

The LTM8023EY#PBF is the commercial temperature grade of the 2 A, 36 V step-down module in the ball grid array body, and its specification window is the one detail that decides whether it can be used at all in a given cabinet. The module itself is the familiar one: controller, switches, inductor and compensation inside a 9 mm by 11.25 mm by 3.42 mm package, 3.6 V to 36 V input, 0.8 V to 10 V output at 2 A, and a switching frequency set between 200 kHz and 2.4 MHz by a single resistor. What the E suffix changes is the guarantee: 0 to plus 85 degrees ambient, with the minus 40 degree end of the operating range assured by characterisation and not by test.

The E grade is a testing statement, not a different die

The data sheet note is explicit: the E grade is guaranteed to meet its performance specifications from 0 to plus 85 degrees ambient, and specifications over the full minus 40 to plus 85 range are assured by characterisation and correlation with statistical process controls, while the I grade is guaranteed over the whole range by test. The silicon is the same. That means an E grade module will usually work below zero, and it also means that a product which specifies operation at minus 20 degrees and ships the E grade has accepted a risk that the data sheet does not cover. For an indoor rack product the risk is negligible, and for an outdoor cabinet it is the difference between a warranty claim and a specification, so the I or MP grade is the defensible choice.

Output setting, frequency and the internal inductor

The output is set by one resistor to ground from the adjust pin, which regulates to 0.79 V, so RADJ equals 394.21 divided by the output voltage minus 0.79, in kilo ohms. A 3.3 V output takes about 157 kohm and a 1.2 V output takes about 962 kohm, and an output below 0.79 V is not available from this part. The frequency resistor sets the switching frequency, and the recommendation is a function of the input and output pair because the inductor is inside the package and cannot be changed. Running well below the recommended frequency raises the ripple current beyond what the recommended output capacitor was chosen for, and running above it raises the switching loss and runs into the minimum on-time at high input voltage.

ParameterValue on this order codeWhat it decides
Temperature guarantee0 to plus 85 degrees by testMinus 40 assured by characterisation only
PackageBGA, 9 mm by 11.25 mm by 3.42 mmBall joints, X-ray or electrical test
Ball finishSAC305, RoHSLead free assembly without a process change
Input range3.6 V to 36 V24 V rails are inside, transients are not
Output0.8 V to 10 V at 2 AOne resistor, 0.79 V threshold
Frequency200 kHz to 2.4 MHzRecommended value follows the voltage pair
Start-up5.5 V with RUN/SS tied to the inputA 5 V rail at tolerance may not start
Moisture sensitivityMSL 3Floor life limits reflow after opening
Power goodWithin 10 percent of regulationSequencing margin has to include it

Where the E grade is the right answer

Rack mounted networking and computing equipment, bench instruments and any product that is specified from 0 to 70 degrees inside a controlled environment are the sockets where the E code is correct and the least expensive. The trap is a product whose marketing says minus 40 degrees while the BOM says E grade, because nothing in the assembly or the test will catch it until the unit is cold. Where the cold end is real, the I grade costs more and removes the question entirely.

Second source and board questions

Because the module contains its own inductor, a substitute is a whole power supply and not a component, so the comparison has to include the internal inductor value, the loop compensation and the recommended external capacitor set, not just the input and output ranges. The ADI part second source page sets out those fields, the pin to pin cross reference covers the body, and the one stop BOM sourcing page covers the module with its capacitors on one order.

The BIAS pin is an efficiency decision, and it has a limit

The module brings out a bias pin that can be connected to the output, or to another rail between 2.5 V and 5 V, to power the internal control circuitry from a lower voltage than the input. At a 24 V or 36 V input that change is worth several points of efficiency, because the control current is then drawn from the output instead of being dropped from the input, and the saving grows with the input voltage. The pin has a maximum voltage that has to be respected and the connection has to be present at start-up as well as in steady state, so a build that ties it to an output rail which is derived from the module itself needs a check that the module can start before that rail exists.