Contact Us

LTM8023EV#PBF

Brand: Analog Devices
Analog Devices LTM8023EV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8023EV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8023EV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8023EV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8023EV#PBF: The Low Profile Commercial Module, and the Three Parts Around It That Matter

The LTM8023EV#PBF is the commercial grade of the 2 A, 36 V step-down module in the land grid array body, 2.82 mm tall, and it is the lowest cost way to get a complete 2 A regulator onto a board from a 3.6 V to 36 V rail. The package contains the controller, the switches, the inductor and the compensation, so the bill of materials around it is bulk input and output capacitors, one resistor for the output voltage and one for the switching frequency. The three external parts that decide whether the module behaves are those capacitors and the two resistors, and each of them has a specific failure mode when it is chosen from a table rather than from the data sheet.

The output capacitor is chosen for ripple, not for stability alone

The module is stable with a defined range of output capacitance, and the data sheet's recommended value is set by the ripple current at the recommended switching frequency. Too little capacitance leaves the ripple above what the load can tolerate and can also move the loop phase margin, and too much electrolytic capacitance with a high equivalent series resistance adds a zero that changes the transient response. The input capacitor has the harder job: it carries the pulsed current of the switching stage, so its ripple current rating at the switching frequency matters more than its capacitance, and a capacitor chosen for its microfarad value alone will heat up and lose capacitance over the life of the product.

The two resistors set the voltage and the frequency, and the second one is not free

The adjust resistor sets the output from the 0.79 V feedback threshold: RADJ equals 394.21 divided by the output voltage minus 0.79, in kilo ohms, which is about 157 kohm for 3.3 V and about 230 kohm for 2.5 V. The frequency resistor sets the switching frequency between 200 kHz and 2.4 MHz, and because the inductor is fixed inside the package, the recommended frequency depends on the input and output pair. A module running at a much lower frequency than recommended will have a larger ripple current than the output capacitor was chosen for, and one running much higher will hit the minimum on-time at high input voltage and start to skip pulses, which shows up as a widening output ripple at light load.

ParameterValue on this order codeWhat it decides
PackageLGA, 9 mm by 11.25 mm by 2.82 mmLowest profile in the family, pads inspectable
Temperature guarantee0 to plus 85 degrees by testCold end assured by characterisation
Input range3.6 V to 36 VUp to 24 V nominal with margin for transients
Output0.8 V to 10 V at 2 A10 W maximum at the top of the range
Feedback threshold0.79 VSets the resistor and the output floor
Frequency200 kHz to 2.4 MHzLower frequency means more ripple current
Soft startCapacitor on RUN/SSLimits inrush into bulk output capacitance
Moisture sensitivityMSL 3Baking required after the floor life expires
FinishGold pads, RoHSe4 finish, no whisker question

The 10 W output at the top of the range

At 10 V out and 2 A the module delivers 20 W, which is the highest dissipation case in its range, and at 36 V in the loss is at its highest at the same time. The 2 A rating is therefore not uniform across the output range, and a 10 V output at 2 A from a 36 V input has to be checked against the derating curves for the actual board copper. The same module at 3.3 V out and 2 A from 12 V in is a comfortable application, which is why most applications of this family sit in the middle of the range rather than at its edges.

Where this code fits

Bench instruments, embedded computers and industrial boards that sit in a controlled environment and need a low profile point of load converter are the correct sockets, and the LGA body suits a line with optical inspection. Where the product is specified below zero, the I grade of the same module is the defensible choice, and where the ambient goes above plus 85 degrees the MP grade is the only specified part. The pin to pin cross reference covers the body choice, the ADI part second source page lists what a substitute module has to match, and the one stop BOM sourcing page covers the module and the capacitors that surround it.

Power good, floating pins and the pin that must not be left undriven

The power good output is an open drain pin that is valid when the input is above 3.6 V and the RUN/SS pin is high, and it can be left floating when the function is not used. The RUN/SS pin is the one that must not be left undriven: tying it to ground shuts the module down, and it has to be at 2.5 V or more for normal operation, so a divider or a direct connection to the input is required on every board even when soft start is not needed. A capacitor from that pin to ground sets the ramp, which is the only inrush control the module offers, and a build that leaves the pin open will behave unpredictably rather than simply running without soft start.