Contact Us

LTM4676AIY#PBF

Brand: Analog Devices
Analog Devices LTM4676AIY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4676AIY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4676AIY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4676AIY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4676AIY#PBF: 26 A, 40 ms of turn on time, and 2.5 percent of current readback at 10 A

The LTM4676AIY#PBF is a dual 13 A or single 26 A step-down module with a PMBus interface, in a 16 mm by 16 mm by 5.01 mm ball grid array. It takes 4.5 V to 26.5 V in and 0.5 V to 5.5 V out, holds plus or minus 0.5 percent of dc output error over temperature, reads current back to plus or minus 2.5 percent at a 10 A load and has a 40 ms turn-on time. It is also pin compatible with the dual 18 A LTM4677, which is the fact that changes how a board is planned: the same footprint can be bought at 13 A or 18 A per channel.

Published values

ParameterValue
Input voltage4.5 V to 26.5 V, 5.75 V to 26.5 V in the typical application
Output voltage0.5 V to 5.5 V
Output currentdual 13 A or single 26 A
DC output errorplus or minus 0.5 percent maximum over temperature
Current readback accuracyplus or minus 2.5 percent at a 10 A load
Turn-on time40 ms
Digital interface400 kHz PMBus compliant I2C, 16-bit ADC, polling to 125 Hz
Non volatile memoryEEPROM fault log with ECC
Pin compatibilityLTM4677, dual 18 A
Thermal resistance10.3 degree C per W, 6.2 degree C per W on the alternative test board
PackageBGA, 16 mm x 16 mm x 5.01 mm
Weight3.3 g

Duty cycle at 26.5 V is 1.9 percent, and that is the input limit in practice

Twenty six and a half volts in and 0.5 V out is a 1.9 percent duty cycle, which at 1 MHz is 18.9 ns of on time. The part will not run that pulse cleanly, so the top of the input range is used with outputs of 1 V and above, where the duty cycle is 3.8 percent or better. A 24 V industrial rail feeding a 0.6 V core rail is the case to check: 2.5 percent duty at 1 MHz is 25 ns, and the answer is usually a lower switching frequency rather than a different module.

The 26 A figure itself is not the limit either. Twenty six amps at 1 V is 26 W, and at 88 percent the input power is 29.5 W, which is 2.46 A from a 12 V rail and 1.11 A from a 26.5 V rail. The 3.5 W of loss at 10.3 degree C per W is a 36 degree C rise, so the thermal case is comfortable at 26 A and becomes the deciding one only when the ambient passes 80 degree C.

What a 40 ms turn-on time rules out

Forty milliseconds from enable to regulation is slow for a core rail and ordinary for a hot swap or a backplane supply. A sequencing budget that allows 50 ms per rail cannot fit this part plus a monitor, and a system that expects a rail up in 5 ms has the wrong module. The number comes from the soft start and the output capacitance rather than from the loop, so it is set by the configuration in the EEPROM and the capacitor bank on the board.

The same 40 ms is a feature when the input is a hot swap rail: the inrush into the output capacitance is spread over that window, and a 26 A module with 2000 uF of output capacitance would otherwise look like a short at the input. That trade is the one to make explicitly, because it moves the problem from the input fuse to the sequencing budget.

Pin compatibility with the 18 A part is a supply chain decision

The LTM4677 is a dual 18 A module in the same footprint and with the same ballout, so a board can be laid out once and populated at 13 A or 18 A per channel depending on what is available and what the thermal case allows. That is 38 percent more current for the same board area, and it is the reason a build that starts on the 13 A part does not have to be re spun when the load grows.

The catch is thermal: the 16 mm square body has 10.3 degree C per W on the vendor test board, and an 18 A part in the same footprint puts 38 percent more loss into the same copper. The board that was comfortable at 26 A is not automatically comfortable at 36 A, and the copper under the module has to be planned for the higher number from the beginning if the upgrade path is real.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, the pin to pin cross reference is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.

Two questions buyers ask

Is the A suffix a different die from the LTM4676? The data sheet describes this part as the pin compatible and improved performance version of the LTM4676, so the A is an improved revision rather than a package option. A board laid out for the earlier part takes the A version, and the improvement shows up in the dc error and readback limits rather than in the pinout.

Does the module need a bus master to regulate? No. Output voltage, switching frequency and channel phase can be set with pin strapping resistors at start-up, and the module regulates without any bus traffic. PMBus is needed for margining, for changing settings at run time and for reading the telemetry and the fault log.