LTM4657IY#PBF
Product Specifications
LTM4657IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4657IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM4657IY#PBF: 8 A in a 6.25 mm square, and the 3.1 V input floor on a 3.3 V rail
The LTM4657IY#PBF is an 8 A step-down module in a 6.25 mm by 6.25 mm by 3.87 mm ball grid array, with the controller, the fets, the inductor and the support parts inside. It runs from 3.1 V to 20 V in and 0.5 V to 5.5 V out, holds plus or minus 1.5 percent of total dc output error over line, load and temperature, and has a differential remote sense amplifier. The number worth reading twice is the 3.1 V input floor: a 3.3 V rail at minus five percent is 3.135 V, which is 35 mV above it and leaves no room for a connector drop.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 3.1 V to 20 V |
| Output voltage | 0.5 V to 5.5 V, set by one resistor |
| Output current | 8 A dc |
| DC output error | plus or minus 1.5 percent over line, load and temperature |
| Remote sense | differential amplifier |
| Solution size | under 1 square cm single sided, 0.5 square cm double sided |
| Pin compatibility | LTM4626 at 12 A and LTM4638 at 15 A |
| Light load behaviour | selectable discontinuous mode |
| Thermal resistance | 17 degree C per W |
| Weight | 497 mg |
| Package | BGA, 6.25 mm x 6.25 mm x 3.87 mm |
| Protection | overvoltage, overcurrent and overtemperature |
Eight amps at 1 V is 8 W, and 1.4 W of that is lost in the package
At 1 V and 8 A the output is 8 W. At 85 percent the input power is 9.4 W, so the loss is 1.4 W and at 17 degree C per W the rise is 24 degree C. From a 12 V rail that is 784 mA of input current. The module is thermally comfortable at its rating in still air, which is what makes the 6.25 mm square footprint credible: the figure that limits it is the 3.87 mm height and the copper under it rather than the silicon.
At 5 V and 8 A the output is 40 W and, at 92 percent, the loss is 3.5 W, which is a 59 degree C rise and a much hotter part. The same module at 1 V and at 5 V is two different thermal problems, and the rating of 8 A does not distinguish between them. A build that wants 8 A at 5 V is at the edge of the package in still air and needs airflow or copper.
The 3.1 V floor is the constraint on a 3.3 V backplane
A 3.3 V rail at minus five percent is 3.135 V, and the module starts at 3.1 V, so there is 35 mV of margin before the connector, the fuse and the trace resistance are counted. A 3.3 V rail driving a 2.5 V load is fine because the dropout is inside the margin; a 3.3 V rail driving a 3.0 V load is not, and a 3.3 V rail driving a 3.3 V load is impossible because the part cannot run at 100 percent duty.
The 20 V top of the input range is the other end, and 20 V to 0.5 V is a 2.5 percent duty cycle. That is the configuration where the minimum on time decides the switching frequency, so a 20 V industrial rail feeding a 0.9 V core rail needs a lower frequency than the same part on a 5 V rail would use. The data sheet's efficiency curves are drawn at fixed input voltages for exactly this reason.
Pin compatible with a 12 A and a 15 A module in the same footprint
The LTM4626 is a 12 A module and the LTM4638 a 15 A module in the same ballout, so a board can be laid out once and populated at 8, 12 or 15 A. That is nearly double the current for the same 6.25 mm square, and it is a supply chain advantage: a shortage on one part number does not stop the build if the higher current part is available and the thermal case allows it.
The thermal case is what has to be checked, because the larger parts put more loss into the same copper, and the 17 degree C per W number belongs to the 8 A part on the vendor test board. Fitting a 15 A part into a board that was checked at 8 A is an electrical substitution and not a thermal one, and the difference shows up as a hot module rather than as a failed test.
Two pages worth reading before a purchase order goes out are the power management cross reference and the pin to pin cross reference; the first lists what else fits the socket, the second is the test sequence for a drop in, and component lead time solutions covers the case where the shortage is already on the line.
Two questions buyers ask
Is the differential sense amplifier required? It is not required, but on a 0.5 V output it is what makes the 1.5 percent figure meaningful. Half a volt at plus or minus 1.5 percent is 7.5 mV, and a ground return carrying 8 A through 1 milliohm drops 8 mV, which is more than the whole error budget. The sense lines are how that drop is taken out of the loop.
What does the selectable discontinuous mode do? It allows the inductor current to stop at light load instead of reversing, which raises efficiency when the load is a few milliamps and produces a slightly larger output ripple. On a rail that sleeps, the mode is worth enabling; on a rail that always carries more than an amp it makes no difference and the continuous mode gives a cleaner waveform.