Contact Us

LTM4637EY#PBF

Brand: Analog Devices
Analog Devices LTM4637EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4637EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4637EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4637EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4637EY#PBF: The Ball Grid Array Body of the 20 A Module, and the Heatsink Question

The LTM4637EY#PBF is the same 20 A step-down module as the rest of the LTM4637 family, in the ball grid array body that stands 4.92 mm tall against the 4.32 mm of the land grid array version. Everything electrical is shared: 4.5 V to 20 V input, 0.6 V to 5.5 V output at 20 A, plus or minus 1.5 percent total direct current error over minus 40 to plus 125 degrees, current sharing to 80 A with four modules, and pin compatibility with the 15 A LTM4627. The choice between the two bodies is mechanical and production led, and at 20 A the mechanical question is a thermal one.

Half a millimetre of height is a thermal decision at 20 A

A 20 A module delivering 1.0 V dissipates in the region of 2.7 W at the efficiency the data sheet quotes, and that heat leaves through the bottom of the package into the board and through the top into whatever is above it. The taller ball grid array body gives a slightly longer path to the board and a slightly flatter top surface to press a heatsink against, which is why builds that use a heatsink often choose the BGA while builds that rely on board copper choose the LGA. The thermal curves in the data sheet are drawn for specific board sizes, copper weights and airflow, and the current a board can actually hold is read from those curves and not from the 20 A line on the front page.

Paralleling four modules for 80 A

Current sharing is done with the current mode loop and a share pin, and it works because each module's error amplifier compares its own output to the common share bus rather than to a fixed reference. The accuracy of the sharing depends on the routing of that bus and on the matching of the output paths, so two modules with equal loads on paper but unequal copper on the board will not share equally. The 80 A figure also assumes the four modules are on a board that can carry 80 A from the modules to the load, which at 1 V is a copper and connector problem long before it is a regulator problem.

ParameterValue on this order codeWhat it decides
PackageBGA, 15 mm by 15 mm by 4.92 mmTaller than the LGA code, flat top for a heatsink
Output current20 A, 80 A with four modulesSharing accuracy depends on the share bus routing
Input range4.5 V to 20 V12 V backplanes directly
Output range0.6 V to 5.5 VOne resistor sets the level
AccuracyPlus or minus 1.5 percent over temperatureIncludes the internal reference and the loop
Duty cycle limit94 percent typical at 500 kHzA 5 V output needs about 5.3 V of input
Minimum on-time100 ns20 V to 0.6 V is not a 1 MHz application
Remote senseDifferential, for outputs at or below 3.3 VRemoves copper drop at the load
Bias regulator5 V internal, about 20 mA of driver current0.3 W of loss at a 20 V input

The bias rail and the input voltage that costs money

The module runs its own 5 V regulator from the input to power the drivers, and that regulator burns the input voltage minus 5 V times the driver current. At 12 V in the loss is about 0.14 W and at 20 V in it is about 0.3 W, so the same 20 A load is thermally easier at the lower input voltage. The data sheet also warns that the internal bias regulator needs its own ceramic capacitor, because it is a linear regulator with a fast loop and a long trace to the capacitor turns it into an oscillator. That capacitor is the single most common reason a module that worked on the bench fails on the board.

Where the BGA body belongs

Line cards and processor rails where a heatsink is pressed onto the module, boards that are X-rayed rather than optically inspected, and products that already use the LTM4627 pinout are the natural sockets for this code. Where the application relies on board copper alone, the lower LGA body is easier to cool and easier to inspect. The pin to pin cross reference covers the family pinout, the ADI part second source page sets out what a substitute module has to match, and the one stop BOM sourcing page covers the module, its capacitors and the thermal hardware together.

Current sharing is a bus question before it is a module question

Four modules in parallel deliver 80 A only if the share bus is routed as a single quiet net that reaches all four in the same way, and if the output copper from each module to the load is symmetric. The current mode loop compares each module's output against the common share signal, so a module whose output path is longer carries less current and runs cooler, which then changes its own reference and pushes the imbalance further. The practical check is to measure the current in each module at full load and at half load, because a sharing error that is invisible at half load becomes a thermal problem at full load, and the derating curves assume the currents are equal.