Contact Us

LTM4632IV#PBF

Brand: Analog Devices
Analog Devices LTM4632IV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4632IV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4632IV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4632IV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4632IV#PBF: the 1.82 mm land grid array and a memory rail under a shield

The LTM4632IV#PBF is the land grid array body of the DDR-QDR4 module: 6.25 mm by 6.25 mm by 1.82 mm with Au pads and MSL 3, against 2.42 mm for the ball grid array. It provides a 3 A VDDQ rail, a 3 A VTT rail that sources and sinks, and a 10 mA VTTR reference at half of VDDQ, from an input of 3.6 V to 15 V. The I grade is -40 C to 125 C and the total output error is 1.5 percent over line, load and temperature.

Published values

ParameterValue
Input voltage3.6 V to 15 V
Output voltage0.6 V to 2.5 V per rail
VDDQ and VTT current3 A each, VTT sinks as well as sources
VTTR10 mA buffered at VDDQ / 2
Package height1.82 mm LGA against 2.42 mm BGA
Pad finishAu, finish code e4
Minimum on time20 ns, minimum off time 45 ns
Junction to ambient20 C/W, 11 C/W to case bottom
Package6.25 mm x 6.25 mm x 1.82 mm LGA, MSL 3
Temperature range-40 C to 125 C, I grade

Where 0.6 mm of height is worth paying for

The two bodies are electrically identical and differ by 0.6 mm in height. On a memory card or a module that slides into a connector with a fixed pitch, that 0.6 mm decides whether the part fits under the shield or has to move to the other side of the board.

The thermal numbers differ slightly between the bodies and the land grid array is quoted at 20 C/W junction to ambient with 11 C/W to the case bottom. At 1.2 V and 3 A the loss is about 0.64 W, a 12.7 C rise, so the height saving costs nothing that this power level can measure.

A memory rail has to sink current

VTT is a termination rail and the memory bus drives it in both directions, so the rail has to absorb current on one data pattern and deliver it on the next. The module is specified to 3 A in both directions and tracks VTT to half of VDDQ, which is the reason the termination resistors can be a simple divider rather than an active network.

The VTTR pin is a 10 mA buffered version of the same half voltage, intended for the reference input of a controller. It is not a termination supply, and a board that ties it to a resistor network will see the reference move with the data pattern.

The 20 ns floor at low output

Minimum on time is 20 ns and minimum off time is 45 ns. At 12 V in and 1.2 V out the duty cycle is 10 percent, so 1 MHz gives a 100 ns on time and 3 MHz gives 33 ns, both above the floor. At 15 V in and 0.6 V out the duty cycle is 4 percent, so 2 MHz is exactly 20 ns and 3 MHz is below it.

That makes the usable frequency a function of the input to output ratio rather than a fixed number, and a specification written as a frequency without an input voltage is incomplete. The same applies to the off time: at 3.6 V in and 2.5 V out the duty cycle is 69 percent, so the off time is 31 percent of the period and 45 ns caps the frequency at about 7 MHz, which the other limits reach first.

What a memory rail does not need

The module carries a power good output, overvoltage input protection and overtemperature protection, and it does not carry a precision voltage monitor. A system that has to log the memory rail within 1 percent needs its own measurement, because the 1.5 percent total error is the module's own specification and the flag only tells you the rail is roughly there.

Burst mode is available on channel 1 only, so a VDDQ rail can be run in burst at light load while VTT stays in forced continuous operation. That asymmetry is deliberate: a termination rail that goes into burst moves with the data pattern, and the memory does not tolerate that.

Sourcing notes for this family: the power management cross reference holds the cross references, the obsolete part cross reference hub is the pre substitution check, and one stop BOM sourcing is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Is the 1.82 mm body a drop-in for the 2.42 mm one? No. The land pattern and the standoff differ. The electrical behaviour is the same, so the change is a board revision rather than a component swap.

Can VTTR drive termination resistors? No. It is a 10 mA buffered reference for a controller input. The termination current belongs on VTT, which is specified to 3 A in both directions.