Contact Us

LTC4151CMS#TRPBF

Brand: Analog Devices
Analog Devices LTC4151CMS#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC4151CMS#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LTC4151CMS#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC4151CMS#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC4151CMS#TRPBF: a 12-bit monitor on an 80 V rail spends its resolution on headroom

The LTC4151CMS#TRPBF is an Analog Devices high side current and voltage monitor that works from 7 V to 80 V and reports through I2C. A single 12-bit converter measures the high side current, the input voltage and one additional external voltage, either in a continuous scan or on demand in snapshot mode. A dedicated shutdown pin drops the quiescent current to 120 uA. The LTC4151-1 and LTC4151-2 variants split the I2C data pins so the bus can be driven through opto-isolators, with the data out inverted on the -1 and not inverted on the -2, which is the difference that decides which side of an isolated barrier the host sits on. Bodies are a 10-lead MSOP, a 10-lead 3 mm by 3 mm DFN and a 16-lead SO. The CMS code in this order is the commercial temperature MSOP. It is grouped with the other converters on the analog and mixed-signal IC line card.

One LSB of the voltage channel is 19.5 mV

Twelve bits over an 80 V span gives 4096 codes and 19.53 mV per code. On a 48 V telecom rail that is 0.041 percent per LSB, and on a 12 V rail it is 0.163 percent per LSB, because the converter does not rescale itself to the rail in use. The resolution is therefore fixed at order time by the top of the range, and a board that monitors a 12 V rail with a part rated to 80 V pays a factor of 6.7 in resolution. Where the current channel is measured across an external sense resistor, the resistor value sets the current per LSB, so the resolution of the current reading is a resistor decision rather than a converter decision.

ParameterVendor figureDerived figure
Operating voltage7 V to 80 V12-bit span fixed at 19.53 mV per LSB
Resolution12 bits on current and both voltages4096 codes, no auto-ranging
LSB on a 48 V railsame span0.041 percent of the rail
LSB on a 12 V railsame span0.163 percent of the rail
Shutdown current120 uA5.76 mW at 48 V, 9.6 mW at 80 V
InterfaceI2C, split data pins on the -1 and -2opto-isolated bus possible
BodiesMSOP-10, DFN-10, SO-16three board footprints, one function

The 7 V floor rules out the low rails it is often asked to watch

The part cannot measure a 5 V or 3.3 V rail, because its own supply and its input range both start at 7 V. In a system with a 48 V bus and a 12 V intermediate rail it can watch the 48 V and the 12 V, but the point of load rails need a different monitor. That is a topology fact that shows up late if the monitor is specified after the rail list is frozen.

Continuous scan against snapshot, and why the difference matters

  • Continuous scan keeps all three channels fresh, so a host poll always returns a recent conversion and the bus has to carry the traffic all the time.
  • Snapshot mode converts on demand, which lowers average bus traffic and power when a supervisor polls once a second.
  • The additional ADC input monitors a voltage that is not the rail itself, such as a battery tap or a board temperature sensor output.
  • Split data pins on the -1 and -2 exist for isolation, and the inverted data on the -1 is what an opto-coupler with a grounded emitter needs.

Questions buyers ask

Does the monitor measure current on the high side? Yes, it sits in the positive rail with an external sense resistor, so the ground reference of the load is not disturbed.

Can it be used on a negative 48 V rail? Not directly. The part is a high side monitor for a positive rail, and a -48 V system needs the sense element and the supply arranged for that polarity.

For monitoring parts across a power tree, the alternates are collected on the ADC DAC cross reference page, and short supply on a specific body is handled through BOM shortage recovery.

Request Quote — In Stock, 100% New & Original, Full Warranty