Contact Us

LTC3890EUH#TRPBF

Brand: Analog Devices
Analog Devices LTC3890EUH#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC3890EUH#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LTC3890EUH#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC3890EUH#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC3890EUH#TRPBF: Two Buck Channels Out of Phase on a 60 V Input

The LTC3890EUH#TRPBF is a dual step-down switching controller that drives all N-channel synchronous MOSFET stages from a 4 V to 60 V input, 65 V absolute maximum, with an output range of 0.8 V to 24 V. The two channels run out of phase, which halves the input capacitor ripple current and the noise the supply injects into the board, and the architecture is constant frequency current mode with a phase lockable frequency from 75 kHz to 850 kHz or a programmable fixed frequency from 50 kHz to 900 kHz. No-load quiescent current is 50 uA with one channel on, shutdown is below 14 uA, the internal LDO can run the gate drive from the input or from an external supply, light load behaviour is selectable between continuous, pulse skipping and a low ripple burst mode, and the part has a power good output and output overvoltage protection. It is AEC-Q100 qualified and comes in a 5 mm by 5 mm QFN 0.75 mm tall.

The out of phase operation is the part of this controller that a two channel product actually buys. Two buck stages switching at the same instant pull their pulses from the input capacitor together, which doubles the RMS ripple the capacitor sees; 180 degrees apart, the pulses interleave and the capacitor current partially cancels.

50 uA at 12 V is 0.6 mW, and 438 mAh over a year

One channel on with no load draws 50 uA, which at a 12 V rail is 0.6 mW and 438 mAh over a year. Shutdown below 14 uA is 123 mAh a year at the same rail. A controller that draws 1 mA instead would take 8.76 Ah over a year from the same 12 V battery, which in a vehicle or a backup unit is the difference between a battery that holds charge over a season and one that does not.

That current is quoted for one channel on, so a product where both channels are enabled pays twice, and one that keeps a single channel alive on a sleep rail and enables the second on demand is the way the figure is meant to be used. The selectable burst mode is the second lever: at light load the controller skips cycles instead of holding continuous conduction, trading ripple for quiescent power.

0.8 V to 24 V is a 30 to 1 output range on the same controller

A 0.8 V reference with a resistive divider gives any output from 0.8 V to 24 V, a factor of 30, which means one controller can serve a 1.0 V core rail and a 12 V intermediate rail on the same board. The 24 V ceiling is a limit of the controller and the components around it, not of the input: a 48 V input system can produce a 12 V output but not a 24 V one with this part.

The input range of 4 V to 60 V covers a 12 V or 24 V battery directly and a 48 V telecom rail with margin. The 65 V absolute maximum leaves 5 V above the 60 V rating for transients, which is thin for an inductive load dump and adequate for a clamped one. The internal LDO that runs the gate drive from the input keeps efficiency high at low duty cycles and can be moved to an external supply when the input is high and the gate charge loss matters.

FunctionDual step-down synchronous controller, out of phase
Input4 V to 60 V, 65 V absolute maximum
Output0.8 V to 24 V per channel, a 30 to 1 range
Quiescent50 uA one channel on, 0.6 mW at 12 V, 438 mAh a year
ShutdownBelow 14 uA
Frequency50 kHz to 900 kHz programmable, 75 kHz to 850 kHz phase lockable
Current sensingSense resistor or inductor DCR
Light loadContinuous, pulse skipping, or low ripple burst mode
HousekeepingPower good, output overvoltage protection, soft start or tracking per channel
Package and grade5 mm by 5 mm QFN, AEC-Q100

Two questions buyers ask

Why does out of phase operation matter if the input is a battery?
Because the input is never a perfect source. Battery impedance, connector resistance and cable inductance turn the input ripple current into a voltage ripple that appears on every other rail fed from the same node. Interleaving the two channels cuts the RMS current the input capacitor has to carry, which allows fewer or smaller capacitors and a quieter board. The same interleaving also moves the switching noise away from a single frequency.

Can it run from a 48 V rail?
Yes, the input rating is 60 V, and a 48 V rail with 10 percent tolerance is 52.8 V, inside the range. The output ceiling of 24 V still applies, so a 48 V to 12 V rail is fine and a 48 V to 24 V rail sits at the limit of the output range. The gate drive then comes from the internal LDO unless an external supply is provided.

Ordering and supply

The EUH suffix is the 5 mm by 5 mm QFN body on the industrial grade, and TRPBF is tape and reel, lead free. The family has fourteen part models across grades and packages, so the exact code is what identifies the body; the same controller in a different package is a different order line. The AEC-Q100 qualification applies to the automotive grades within the family, not automatically to every code.

We supply this family for production and for repair. Start at the analog mixed signal ICs family page, compare a candidate against the power management cross reference, and where a controller has to be found during a shortage, the recovery sequence in BOM shortage recovery is the place to start rather than a wildcard search.

Request Quote — In Stock, 100% New & Original, Full Warranty