AD8608ARZ
Product Specifications
AD8608ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8608ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8608ARZ: 1 pA of Input Bias at 25 C Becomes 750 pA at 125 C
The AD8608 is the quad member of the AD8605, AD8606, AD8608 family: 65 uV maximum offset voltage, 1 pA maximum input bias current, 8 nV per root hertz of voltage noise and 10 MHz of unity gain bandwidth on a 2.7 V to 5.5 V single supply, specified from minus 40 C to plus 125 C. The 1 pA number is a 25 C figure, and the same table carries 750 pA maximum over the full temperature range. On a photodiode preamplifier or a high impedance bridge that difference is the whole error budget, and it is the reason the part is often chosen for one grade of product and then fails at temperature on another.
What a picoamp means at the source impedance you actually have
Bias current turns into voltage in the source resistance. At 1 pA and 10 Mohm the error is 10 uV; at 750 pA and the same 10 Mohm it is 7.5 mV, which is a hundred times the 65 uV offset the part is bought for. At 1 Mohm the two cases are 1 uV and 0.75 mV. The crossover where bias current stops mattering is around one megaohm at 25 C and around one hundred kiloohm at 125 C, and that shift is what a temperature sweep on the bench will show.
Noise and bandwidth together
8 nV per root hertz at 1 kHz integrates to 2.53 uV over a 100 kHz band and to 8 uV over a 1 MHz band. With a 10 MHz gain bandwidth, a gain of 100 leaves 100 kHz of closed loop bandwidth, so the integrated noise in that configuration is the 2.53 uV figure and not the 1 MHz one. The 0.1 Hz to 10 Hz peak to peak noise is 2.3 uV typical and 3.5 uV maximum, which matters for a DC instrument and does not for an AC coupled one.
| Item | Published value | Where it bites |
|---|---|---|
| Offset voltage | 65 uV maximum | DC accuracy at the input |
| Bias current | 1 pA at 25 C, 750 pA over temperature | High impedance sources |
| Voltage noise | 8 nV per root hertz at 1 kHz | Integrates to 2.53 uV over 100 kHz |
| Gain bandwidth | 10 MHz | 100 kHz closed loop at a gain of 100 |
| Supply current | 1.0 mA typical per amplifier | 4.8 mA for the quad |
Rail to rail input is a claim about the common mode range, not the output
The input common mode range covers the full supply on this family, and the output swings to within a few tens of millivolts of each rail at light load, with the number widening as the load current rises. A follower that has to sit at the positive rail at 10 mA of load should be checked against the output swing column rather than the headline, and a stage that only needs the input near the rail is the case this part is built for.
Slew rate and settling for a multiplexed input
The slew rate is 5 V per microsecond, and settling to 0.01 percent on a 2 V step takes under a microsecond. With four amplifiers in one package, the usual use is a four channel input stage ahead of a multiplexer or a converter, and the settling figure is what sets the channel to channel timing. A 1 V step takes about 200 ns of slewing plus the settling tail, so a 1 MSPS converter switching between four channels is inside the timing with margin and a 4 MSPS one is not.
Ordering the quad against two duals
Two AD8606 duals in the same board give the same electrical performance with a different thermal and routing picture, and the pinouts are not interchangeable. The amplifier cross reference page covers that substitution, the medical device components page covers the supply chain side, and lot checks follow the incoming inspection plan.