Contact Us

AD620BRZ

Brand: Analog Devices
Analog Devices AD620BRZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD620BRZ — Analog & Mixed-Signal ICs | Superb Automation

AD620BRZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD620BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD620BRZ: Drift Over Temperature Is Larger Than the Offset the Part Is Bought For

The AD620 is the instrumentation amplifier that most gain stages are measured against: one external resistor sets a gain from 1 to 10,000, the supply range is 2.3 V to 18 V, the supply current is 1.3 mA maximum, the input bias current is 1 nA maximum and the common mode rejection is 100 dB minimum at a gain of 10. The offset voltage on the B grade is 50 uV maximum with a drift specified at 0.6 uV per degree C maximum. Over a 125 degree span that drift is 75 uV, so the part at temperature is less accurate than the part on the datasheet line.

Gain is one resistor and one arithmetic step

The gain equation is 49.4 kohm divided by the gain resistor plus one. A gain of 100 needs 499 ohm, a gain of 1000 needs 49.4 ohm, and a gain of 10,000 needs 4.94 ohm. At the top of the range the resistor is smaller than the tolerance of the wiring, so a 1 percent resistor is a 1 percent gain error and the resistance of the two tracks to it is part of the gain. That is why high gain instrumentation stages are trimmed on the finished board rather than trusted to the resistor value.

Bandwidth falls in proportion to gain

The published bandwidth is 120 kHz at a gain of 100, which sets the unity gain crossover at about 12 MHz. At a gain of 1000 the closed loop bandwidth is 12 kHz and at 10,000 it is 1.2 kHz. A weigh scale running at a gain of 200 therefore has about 60 kHz of bandwidth, which is ample for a 10 Hz output rate; a vibration channel at a gain of 1000 with a 10 kHz requirement is outside the part and needs a different amplifier.

ItemPublished valueWhat it decides
Gain range1 to 10,000, one resistor49.4 kohm divided by R plus one
Offset, B grade50 uV maximumDC accuracy at the input
Drift0.6 uV per degree C maximum75 uV over 125 C
Bias current1 nA maximum1 mV into 1 Mohm
Noise9 nV per root hertz at 1 kHz2.85 uV over 100 kHz at the input

Noise against source resistance

9 nV per root hertz integrates to 2.85 uV over a 100 kHz band, and the 0.1 Hz to 10 Hz peak to peak noise is 0.28 uV, which is 1.4 percent of a 16 bit LSB on a 2.5 V full scale. A 350 ohm bridge contributes 2.4 nV per root hertz of thermal noise, so the amplifier dominates below about 1 kohm of source resistance and the bridge dominates above it. A 10 kohm source makes the amplifier noise irrelevant and the bias current the problem instead.

The reference pin is not a spare input

The REF pin shifts the output by the voltage applied to it, and it must be driven from a low impedance. A 10 kohm by 10 kohm divider from the supply puts 5 kohm of source resistance on the reference, and the amplifier's own common mode rejection of 100 dB does not remove the divider's drift. On a single supply board the reference is usually tied to mid rail through a buffer, and the buffer is part of the error budget, not an afterthought.

Substitution and grade questions

The A grade is 125 uV of offset and the B grade 50 uV, so the two are a test grade and not a die change, and a validated B grade board can usually take the A grade with a recalibration. The amplifier cross reference page covers the in amp families that share a pinout, the medical device components page covers the supply chain side for instrument front ends, and lot checks follow the incoming inspection plan.