Contact Us

LTC1628CG#PBF

Brand: Analog Devices
Analog Devices LTC1628CG#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC1628CG#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTC1628CG#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC1628CG#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC1628CG#PBF: Two Out of Phase Controllers, 3.5 V to 30 V In, and the Parts You Still Have to Choose

The LTC1628CG#PBF is a dual step-down switching regulator controller in a 28-lead SSOP that drives all N-channel synchronous power stages. It operates from 3.5 V to 30 V with a 36 V maximum, switches at a resistor programmed frequency from 150 kHz to 300 kHz, holds plus or minus 1 percent output accuracy, runs its two channels out of phase to reduce input capacitor ripple, supports 99 percent duty cycle for low dropout operation, and includes soft start, foldback current limiting, a latched short circuit shutdown with a defeat option, output overvoltage protection, remote output voltage sense, a 20 uA shutdown current and on-chip 5 V and 3.3 V standby regulators. The -PG version replaces the fault coupling pin with a power good output, and a selectable mode chooses between constant frequency and burst operation.

This is a controller, not a converter: the MOSFETs, the inductors, the current sense resistors and the compensation network are all outside the package, and the part's job is to drive them correctly. That is what makes it flexible and what makes the loss and the thermal path the buyer's problem rather than the vendor's.

Out of phase means the input capacitor sees twice the frequency

Two channels at 300 kHz running 180 degrees apart produce input current pulses at 600 kHz, so the input capacitor sees twice the ripple frequency and roughly half the RMS ripple current of two independent converters. That is the difference between four electrolytic capacitors and two, and it is the reason the two channels belong in one package rather than two. At 150 kHz the same arrangement gives 300 kHz of input ripple, which is still above the audio band and below the conducted emission limits that start at 150 kHz.

The plus or minus 1 percent output accuracy is 33 mV on a 3.3 V rail and 18 mV on a 1.8 V rail, which is tight for a controller whose reference and error amplifier are inside the package but does not include the tolerance of the feedback divider. The divider is where the accuracy is usually lost: two 1 percent resistors add 2 percent of ratio error, which is twice the part's own specification, so a precision rail needs 0.1 percent resistors or a trim.

TopologyDual step-down controller, N-channel synchronous stages
Input3.5 V to 30 V operating, 36 V maximum
Frequency150 kHz to 300 kHz, programmed by a resistor, two channels out of phase
Input ripple600 kHz at a 300 kHz setting, half the RMS current of two independent converters
AccuracyPlus or minus 1 percent, 33 mV on 3.3 V and 18 mV on 1.8 V before the divider
Duty cycle99 percent, so a 3.5 V input can hold a 3.3 V output at 94 percent
On time917 ns at 300 kHz from 12 V to 3.3 V
Shutdown20 uA, 240 uW at 12 V, 175.2 mAh over a year
ProtectionFoldback current limit, latched short circuit shutdown, output overvoltage
ExtrasOn-chip 5 V and 3.3 V standby regulators, remote sense, soft start

Ninety nine percent duty is not one hundred

At a 3.5 V input and a 3.3 V output the required duty cycle is 94 percent, which the controller can produce, so a 3.5 V rail can hold a 3.3 V output at 300 kHz with 917 ns of on time. What it cannot do is pass the input through: 99 percent is the ceiling, so a 3.3 V input into a 3.3 V output is outside the part even though a converter with 100 percent duty would manage it in dropout. A board that has to survive a 3.3 V rail sagging to 3.0 V needs a different topology, not a different resistor.

The 20 uA shutdown current is 240 uW at 12 V and 175.2 mAh over a year, which matters in a product that is off more than it is on. The two standby regulators are linear and are meant for a housekeeping rail, not for the main load: they run from the input and dissipate the difference between input and output as heat, so a 24 V input feeding a 3.3 V standby load of 10 mA would burn 207 mW in the package. That is the trade against a third switching channel.

Two questions buyers ask

What is the difference between the LTC1628 and the LTC1628-PG?
The -PG version replaces the fault coupling control pin with a power good output that reports when the output is in regulation. The fault coupling pin on the plain part lets one channel respond to a fault on the other, which is useful in a system where both rails supply the same load. A board that needs a power good signal for a supervisor needs the -PG, and the two are otherwise the same controller.

Can the two channels be paralleled for more current?
Not directly. The channels are independent controllers with their own feedback and current limit, and paralleling them requires current sharing circuitry that this part does not include. Two channels driving separate rails is the intended use, and a single higher current rail needs a single channel controller with a larger stage.

Ordering and supply

The CG suffix is the commercial grade in the 28-lead SSOP, also offered in a 5 mm by 5 mm QFN. Substitution traps are the -PG option, the input ceiling and the gate drive: a part with a 20 V input maximum will not run from a 24 V rail, and a controller that cannot drive the chosen MOSFETs at the switching frequency will run hot for reasons that are outside its own specification.

We hold and source this family for production and repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the power management cross reference, and where a controller has to be replaced on an existing board, the order in how to verify a drop in replacement starts with the input ceiling and the gate drive.

Request Quote — In Stock, 100% New & Original, Full Warranty