LTC1387CG#TRPBF
Product Specifications
LTC1387CG#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC1387CG#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC1387CG#TRPBF: Two RS232 Ports or One RS485 Port From a Single 5 V Supply
The LTC1387CG#TRPBF is a reconfigurable CMOS transceiver in a 20-pin SSOP that can be configured either as two single ended RS232 ports or as one differential RS485 and RS422 port, from a single 5 V supply. An on-board charge pump with four 0.1 uF capacitors generates the boosted positive and negative rails that let the RS232 drivers meet plus or minus 5 V output swing from 5 V alone. Supply current is 7 mA typical and 5 uA in shutdown, the receiver inputs withstand plus or minus 25 V, the RS485 driver slew rate is selectable between fast and slow by a logic pin, driver and receiver enables are separate, and a loopback mode connects the driver outputs back to the receiver inputs for self test.
One part that speaks both protocols is worth a board revision in any product that ships to more than one market: a point of sale terminal, an industrial controller or a protocol converter that has to support legacy RS232 and modern RS485 without two separate assemblies.
Seven milliamps is 61 amp hours a year if it never sleeps
Seven milliamps at 5 V is 35 mW, and over a year it is 61.3 Ah, which is more than most battery packs hold. The 5 uA shutdown is 1400 times lower and gives 43.8 mAh a year, so the shutdown pin is not a refinement on this part, it is what makes it usable in anything that runs from a battery. The interface is enabled per port and per direction, so a product that polls a bus once a second can be off for 99 percent of the time and average about 75 uA rather than 7 mA.
The charge pump is the reason the part can do RS232 at all from 5 V. The RS232 specification wants plus and minus 5 V of driver swing, which is 10 V peak to peak, and a 5 V rail cannot produce it without inversion and doubling. Four 0.1 uF capacitors do that job, and their ESR and placement are part of the specification: a charge pump with long traces and cheap capacitors produces a swing that looks fine unloaded and collapses into a 3 kOhm receiver load.
| Configuration | Two RS232 ports or one RS485 and RS422 port, selected by logic |
| Supply | Single 5 V, with an on-board charge pump for plus and minus 5 V |
| Current | 7 mA typical, 35 mW, 61.3 Ah over a year if never shut down |
| Shutdown | 5 uA, 1400 times lower, 43.8 mAh over a year |
| Receiver input rating | Plus or minus 25 V |
| Charge pump | Four 0.1 uF capacitors |
| Diagnostics | Loopback mode, separate driver and receiver enables |
| Slew rate | Fast or slow selected by a logic pin on the RS485 driver |
| Package | 20-pin SSOP, also a wide body option |
The receiver rating is five times the driver swing
The receivers tolerate plus or minus 25 V while the drivers produce plus or minus 5 V, and the asymmetry is deliberate: the danger to a receiver is not the local driver but a distant one on a long cable with a ground potential difference, and the RS232 specification itself requires the receiver to survive 25 V. A part that meets the swing requirement with 5 V drivers but only tolerates 12 V on the inputs is not fully compliant, and the difference only appears in an installation with a grounded cable and two powered devices at different earth potentials.
The selectable slew rate is the other practical feature. A fast RS485 edge radiates and reflects on a long unterminated cable, and a slow edge limits the data rate but survives the cable. A product that has to support both a 10 metre cable at 115 kbit and a 1 metre cable at 10 Mbit cannot do it with one slew rate, and the logic pin makes the choice a firmware setting rather than a board variant.
Two questions buyers ask
Do the two ports work at the same time?
No. The part is reconfigured, not duplicated: it is either two RS232 ports or one RS485 port. The device contains the drivers and receivers for both arrangements, and the mode pin decides which set is connected to the pins. A product that needs both protocols simultaneously needs two parts.
What happens if the cable is unplugged while transmitting?
The drivers have short circuit and thermal shutdown protection, and the RS485 driver holds high impedance when disabled, when the outputs are forced beyond the rails, and when the power is off. The receivers keep a defined output when their inputs float or are shorted to ground, which is what stops a disconnected cable from producing a stream of random bytes into the processor.
Ordering and supply
The CG suffix is the commercial temperature grade in the 20-pin SSOP. Substitution traps are the protocol configuration, the charge pump capacitor count and the receiver rating: a part that is RS485 only cannot be configured as two RS232 ports, and a part with a 12 V receiver rating is a field failure waiting for a long cable. The 25 V rating is part of the standard rather than an optional margin.
We hold and source this family for production and repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the pin to pin cross reference, and where an interface part has to be replaced on a built board, the order in how to verify a drop in replacement starts with the protocol mode and the receiver rating.
Request Quote — In Stock, 100% New & Original, Full Warranty